<![CDATA[iFixit - Answers With Device "Pentax K200D"]]> https://www.ifixit.com/Answers/Device/Pentax_K200D?rss=yes en-US Sat, 04 Apr 2026 23:11:38 -0700 <![CDATA[Pentax K200D: battery power indicator flashing outline only]]> When switching on, battery indicator flashes with outline only, camera not operating. Same thing with new batteries.

⟐ Commented May 04, 2024 at 14:58 MST

]]> https://www.ifixit.com/Answers/View/256586/battery+power+indicator+flashing+outline+only https://www.ifixit.com/Answers/View/256586 Sat, 04 May 2024 14:58:25 -0700 <![CDATA[Pentax K200D: After self-repair, flash and autofocus aren't working properly]]> For the longest time, my Pentax K200D had been inexplicably stuck in autofocus. Since it has been out of warranty for about three years, it didn't seem worth paying the potentially insane repair costs for something so simple. I had no idea what needed fixing or how I could possibly fix it, so I just used it as is. Recently however, I did some research and discovered that it had to either be the autofocus coupler or the MF/AF switch itself. Since the coupler depressed into the lens mount when the lens release was pressed like it was supposed to, I figured it must be the switch and that I could probably fix it myself.

I constructed a capacitor discharge tool out of 12AWG 600 V wires, a 20k Ohm 10W resistor, shrink tubing, and solder like the one constructed in this guide, so I could safely work on the camera, and after opening the it, I discharged the capacitor. All seemed fine and nothing looked or smelled fried.

After a little looking around, I discovered that the issue actually dealt with a small metal clip on the inside of the MF/AF switch that is attached to the front cover of the camera. The clip, which usually sits between the raised ends of a plastic bracket and moves the switch mechanism on the camera body up and down, was bent too far forward and was missing the bracket entirely. I bent it back toward the bracket a bit and voila, the coupler depressed when set to manual and reemerged when set to autofocus!

I reassembled the camera, turned it on, tested out the manual focus and it worked like a charm. However, when I went to test the autofocus, I was once again disappointed. When pressing the shutter down halfway in autofocus now, the camera's focus ring twitches between ∞ and 3ft repeatedly, never actually focusing or taking a photo. On top of that the flash no longer works in either mode. Did I adjust the clip too much and potentially short out the flash circuitry, even though I was doing everything as I thought I should? Please help me, iFixit community!

⟐ Commented October 09, 2016 at 21:46 MST

]]> https://www.ifixit.com/Answers/View/110944/After+self-repair,+flash+and+autofocus+aren't+working+properly https://www.ifixit.com/Answers/View/110944 Sun, 09 Oct 2016 21:46:48 -0700 <![CDATA[Pentax K200D: mode dial wheel is confused]]> I disassembled the mode dial of my pentax k200. Now it seems the camera can not be set to the proper program mode like “P” “Av” etc

The inside of the dial is a brush that triggers contacts on a contact wheel.

Is there a procedure i have to follow when putting it back together so the correct mode setting is recognized?

]]> https://www.ifixit.com/Answers/View/628797/mode+dial+wheel+is+confused https://www.ifixit.com/Answers/View/628797 Thu, 16 Apr 2020 03:27:38 -0700 <![CDATA[Pentax K200D: Aperture of my Pentax k-r]]> My k-r aperture shows F- - and images can't be shown

]]> https://www.ifixit.com/Answers/View/552521/Aperture+of+my+Pentax+k-r https://www.ifixit.com/Answers/View/552521 Sat, 02 Mar 2019 09:57:47 -0700