Fix Your Stuff Community Store

Free Shipping on Domestic Orders $75+

eufy Clean RoboVac G32 Pro Power Control Buttons Replacement

Introduction

If your Eufy Robovac G32 Pro's power and control buttons aren't working, then follow this guide to replace them. There are three main power and control buttons, a spot cleaning button, a recharge button, and an auto cleaning start/pause button. The power and control buttons could not be working due to something blocking the sensor, or the board itself is broken.

What you need

  1. eufy Clean RoboVac G32 Pro Power Control Buttons Replacement, Rolling Brush: step 1, image 1 of 1

    • Make sure your device is turned off.

    • Flip the device upside down on a flat surface.

    Edit

  2. eufy Clean RoboVac G32 Pro Power Control Buttons Replacement: step 2, image 1 of 1

    • Press the clips at the bottom of the device that are indicated by the downward facing arrows.

    • Take off the rolling brush cover.

    Edit

  3. eufy Clean RoboVac G32 Pro Power Control Buttons Replacement: step 3, image 1 of 1

    • Pull the rolling brush up on the right side. Remove the rolling brush.

    Edit

  4. eufy Clean RoboVac G32 Pro Power Control Buttons Replacement, Bump Sensor: step 4, image 1 of 3 eufy Clean RoboVac G32 Pro Power Control Buttons Replacement, Bump Sensor: step 4, image 2 of 3 eufy Clean RoboVac G32 Pro Power Control Buttons Replacement, Bump Sensor: step 4, image 3 of 3

    • Orient the device so the underside is facing up.

    • Remove the eight 9.3 mm screws securing the bumper brackets using a Phillips #1 screwdriver.

    • Remove the bumper brackets.

    Edit

  5. eufy Clean RoboVac G32 Pro Power Control Buttons Replacement: step 5, image 1 of 2 eufy Clean RoboVac G32 Pro Power Control Buttons Replacement: step 5, image 2 of 2

    • Lift the bumper off of the device gently.

    • Use your fingers to disconnect the 8 pin connector.

    Edit

  7. eufy Clean RoboVac G32 Pro Power Control Buttons Replacement: step 6, image 1 of 2 eufy Clean RoboVac G32 Pro Power Control Buttons Replacement: step 6, image 2 of 2

    • Remove the two 10 mm screws using a Philips #1 screwdriver.

    Edit

  8. eufy Clean RoboVac G32 Pro Power Control Buttons Replacement: step 7, image 1 of 1

    • Lift the bump sensor off using your fingers.

    Edit

  9. eufy Clean RoboVac G32 Pro Power Control Buttons Replacement, Power Control Buttons: step 8, image 1 of 2 eufy Clean RoboVac G32 Pro Power Control Buttons Replacement, Power Control Buttons: step 8, image 2 of 2

    • Remove the dust collector by grabbing under the lip and pulling it out.

    Edit

  10. eufy Clean RoboVac G32 Pro Power Control Buttons Replacement: step 9, image 1 of 1

    • Remove the two 5.5 mm screws using a Philips #1 screwdriver.

    Edit

  11. eufy Clean RoboVac G32 Pro Power Control Buttons Replacement: step 10, image 1 of 2 eufy Clean RoboVac G32 Pro Power Control Buttons Replacement: step 10, image 2 of 2

    • Remove the eight 14 mm screws using a Philips #1 screwdriver.

    Edit

  12. eufy Clean RoboVac G32 Pro Power Control Buttons Replacement: step 11, image 1 of 1

    • Lift the bottom housing towards the front.

    Edit

  13. eufy Clean RoboVac G32 Pro Power Control Buttons Replacement: step 12, image 1 of 2 eufy Clean RoboVac G32 Pro Power Control Buttons Replacement: step 12, image 2 of 2

    • Remove the six 5.5 mm screws securing the button board with a Phillips #1 screwdriver.

    Edit

  14. eufy Clean RoboVac G32 Pro Power Control Buttons Replacement: step 13, image 1 of 1

    • Grab the 8 pin connector with your hands and firmly pull it away from the board.

    • Remove the board.

    Edit
Conclusion

To reassemble your device, follow the above steps in reverse order.
Take your e-waste to an R2 or e-Stewards certified recycler.
Repair didn’t go as planned? Try some basic troubleshooting or ask our Answers community for help.

Author

with 1 other contributor

Gabe Moore

Member since: 09/19/24

133 Reputation

1 Guide authored

Badges: 3

Team

University of North Texas, Team 2-5, Coppersmith Fall 2024 Member of University of North Texas, Team 2-5, Coppersmith Fall 2024

UNT-COPPERSMITH-F24S2G5

4 Members

4 Guides authored

0 Guide Comments

Add Comment

View Statistics:

Past 24 Hours: 0

Past 7 Days: 0

Past 30 Days: 5

All Time: 176