Fix Your Stuff Community Store

Free Shipping on Domestic Orders $75+

Razer DeathAdder V3 Pro Macro Buttons Replacement

Introduction

If your Razer DeathAdder V3 Pro's macro buttons are unresponsive to input, stuck, or respond incorrectly, you may need to replace the macro buttons.

For any quick fixes, please visit our troubleshooting guides for the Razer DeathAdder V3 Pro Scroll Wheel Not Responding to Input and Razer DeathAdder V3 Pro Spotty Wired Connection.

Before you begin the replacement, please make sure that you have unplugged and powered off the device.

What you need

  1. Razer DeathAdder V3 Pro Macro Buttons Replacement, Scroll Wheel: step 1, image 1 of 3 Razer DeathAdder V3 Pro Macro Buttons Replacement, Scroll Wheel: step 1, image 2 of 3 Razer DeathAdder V3 Pro Macro Buttons Replacement, Scroll Wheel: step 1, image 3 of 3

    • Use a pry tool or fingernail to carefully remove the large foot on the lower end of the mouse.

    • Remove the three 7 mm screws using a Torx T6 screwdriver.

    Edit

  2. Razer DeathAdder V3 Pro Macro Buttons Replacement: step 2, image 1 of 2 Razer DeathAdder V3 Pro Macro Buttons Replacement: step 2, image 2 of 2

    • BEFORE YOU OPEN THE MOUSE: Be careful at this point. Both shells are connected with a cable in the front of the mouse.

    • Insert a spudger into the seam between the top and bottom shells.

    • Gently work around the edges unclipping the internal latches.

    • Slowly lift the top shell but do not remove it yet; the cables are still attached to the circuit board.

    • Carefully pull the shells apart to unplug the cable in the front.

    Edit

  4. Razer DeathAdder V3 Pro Macro Buttons Replacement: step 3, image 1 of 2 Razer DeathAdder V3 Pro Macro Buttons Replacement: step 3, image 2 of 2

    • Using a small pry tool or your fingers, gently pop the scroll wheel up and out of its housing

    Edit

  5. Razer DeathAdder V3 Pro Macro Buttons Replacement, Macro Buttons: step 4, image 1 of 1

    • Unplug the ribbon cable connected to the side macro buttons from its raised position on the left.

    • Remove the macro buttons.

    Edit

  6. Razer DeathAdder V3 Pro Macro Buttons Replacement: step 5, image 1 of 2 Razer DeathAdder V3 Pro Macro Buttons Replacement: step 5, image 2 of 2

    • Use a spudger to remove the solder covering the switch, then pop off the faulty switch.

    • Apply flux, then use a soldering iron to heat the old solder.

    • Make sure to solder in a well-ventilated area.

    • Clean off the melted solder.

    Edit

  7. Razer DeathAdder V3 Pro Macro Buttons Replacement: step 6, image 1 of 1

    • Apply flux to the removal sites of the switches.

    • Solder the new switches into the areas where the original switches were removed.

    Edit
Conclusion

To reassemble your device, follow these instructions in reverse order.

One other person completed this guide.

Author

with 2 other contributors

Matthew Garcia

Member since: 09/24/25

197 Reputation

1 Guide authored

Badges: 4

+1 more badge

Team

Texas Tech, Team 2-5, Johansen Fall 2025 Member of Texas Tech, Team 2-5, Johansen Fall 2025

TTU-JOHANSEN-F25S2G5

5 Members

5 Guides authored

0 Guide Comments

Add Comment

View Statistics:

Past 24 Hours: 1

Past 7 Days: 10

Past 30 Days: 58

All Time: 199