Skip to main content

Free Shipping on Domestic Orders $75+

GD Midea FT30-3D Fan Base Disassembly

Views: 2.3K

View statistics:

Past 24 Hours:
1
Past 7 Days:
21
Past 30 Days:
130
All Time:
2,315
Comments: 0

No one has left comments on this guide. Will you be first?

Go to guide comments
Completed: 6

6 people have marked this guide "completed." Will you be next?

Favorites: 7

7 people have favorited (and subscribed to) this guide. Will you be next?

Time Required: 20 minutes
Difficulty: Moderate
Action Shots

Be an action hero! This guide needs images that better demonstrate how to perform specific actions.

Better Introduction

Improve this guide by completing or revising its introduction.

GD Midea FT30-3D Fan Base Disassembly

Introduction

Go to step 1 ↓

Repairing the fan's wiring if it is damaged.

What you need

Tools

    1. GD Midea FT30-3D Fan Base Disassembly, Bottom Base: step 1, image 1 of 1
      • Locate and remove the 14.5 mm Phillips #1 screw on the bottom of the fan base.

      Ask FixBot

      Add Comment

    2. GD Midea FT30-3D Fan Base Disassembly: step 2, image 1 of 2 GD Midea FT30-3D Fan Base Disassembly: step 2, image 2 of 2
      • Locate the gray base support release tabs found on either side pictured in the first image.

      • There are release tabs on each side of the base.

      • Press both release tabs in with the tip of your fingers and pull the gray base support until the tabs are cleared.

      Ask FixBot

      Add Comment

    3. GD Midea FT30-3D Fan Base Disassembly: step 3, image 1 of 1
      • Continue removing the gray base support by pressing your thumb into the circular opening in the base and pulling with your figures on the back side.

      • Notice that on the internal front tip of the base there is a tab. Because of this tab the back end will pivot off at that point.

      Ask FixBot

      Add Comment

    4. GD Midea FT30-3D Fan Base Disassembly: step 4, image 1 of 1
      • After the base has separated more it will be easy to fully remove it. Continue pulling the back edge of the gray base support, rotating it around the front tab until it comes off completely.

      Ask FixBot

      Add Comment

    5. GD Midea FT30-3D Fan Base Disassembly: step 5, image 1 of 1
      • Remove the following five 14.5 mm Phillips #1 screws found on the bottom.

      • All of the screws are recessed by 17.5 mm, so ensure your screwdriver can reach that far.

      Ask FixBot

      Add Comment

    6. GD Midea FT30-3D Fan Base Disassembly: step 6, image 1 of 1
      • Once all five screws have been removed the base cover should fall right off with out any effort.

      • When putting the base cover back on; be careful to make sure that none of the wires are pinched.

      Ask FixBot

      Add Comment

Conclusion

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

6 other people completed this guide.

Alan Su

Member since: 10/03/12

846 Reputation

6 Guides authored

Team

Cal Poly, Team 24-28, Regan Fall 2012 Member of Cal Poly, Team 24-28, Regan Fall 2012

CPSU-REGAN-F12S24G28

4 Members

120 Guides authored

0 Guide Comments

Add Comment

View Statistics:

Past 24 Hours: 1

Past 7 Days: 21

Past 30 Days: 130

All Time: 2,315