Fix Your Stuff Community Store

Free Shipping on Domestic Orders $75+

Beats Pill 2024 Tweeter Replacement

Introduction

This guide gives details about how to replace the tweeter (speaker) in the 2024 Beats Pill. A speaker replacement might be needed after unsuccessful troubleshooting of a gargled sound or a non-functioning speaker.

There is a prerequisite guide that follows steps to replace the pill's subwoofer. Please follow the Subwoofer Replacement guide up to step 6, then use the rest of the speaker guide for its replacement.

What you need

  1. Beats Pill 2024 Tweeter Replacement, Subwoofer: step 1, image 1 of 1

    • Remove the strap.

    Edit

  2. Beats Pill 2024 Tweeter Replacement: step 2, image 1 of 2 Beats Pill 2024 Tweeter Replacement: step 2, image 2 of 2

    • With the Beats Pill sitting on a flat surface, insert a spudger into the seam between the chassis and grille.

    • Slide the spudger around the entire perimeter of the grille to sever the adhesive securing the grille.

    • Reapply adhesive when reinstalling the grille.

    • Remove the grille.

    Edit

  3. Beats Pill 2024 Tweeter Replacement: step 3, image 1 of 2 Beats Pill 2024 Tweeter Replacement: step 3, image 2 of 2

    • Use a spudger to remove the six stickers on the face of the driver assembly.

    • Place the stickers on a clean surface so as not to ruin the adhesive.

    Edit

  5. Beats Pill 2024 Tweeter Replacement: step 4, image 1 of 1

    • Use a Phillips #1 screwdriver to remove the six 14.3 mm screws that secure the driver assembly and speaker body together.

    Edit

  6. Beats Pill 2024 Tweeter Replacement: step 5, image 1 of 2 Beats Pill 2024 Tweeter Replacement: step 5, image 2 of 2

    • Insert a spudger into the seam between the driver assembly and speaker body.

    • Gently slide the spudger around the perimeter while prying to separate the driver assembly from the speaker body.

    • This should not require much force.

    Edit

  7. Beats Pill 2024 Tweeter Replacement: step 6, image 1 of 1

    • Disconnect the two subwoofer connections from their motherboard sockets.

    • Depress the clip on each connector prior to removal.

    • Use tape or a marker to mark where each connector goes.

    • If you're completing a tweeter replacement, skip to Step 8.

    Edit

  8. Beats Pill 2024 Tweeter Replacement: step 7, image 1 of 1

    • Use a Phillips #1 screwdriver to remove the four 12.4 mm screws securing the subwoofer.

    • Use a spudger to lift the subwoofer up and off of the driver assembly.

    • This might require some force, as there is adhesive holding the subwoofer to the assembly.

    • During reassembly, apply an adhesive to the new subwoofer before reinstallation.

    Edit

  9. Beats Pill 2024 Tweeter Replacement, Tweeter: step 8, image 1 of 2 Beats Pill 2024 Tweeter Replacement, Tweeter: step 8, image 2 of 2

    • Use a Phillips #1 screwdriver to remove the four 12.4 mm Phillips screws that secure the tweeter.

    • Use a spudger to pry the tweeter away from the driver assembly.

    • This might require some force as there is adhesive securing the tweeter to the driver assembly.

    • Apply adhesive to the replacement tweeter before installation.

    Edit
Conclusion

To reassemble your device, follow the above steps in reverse order.
Take your e-waste to an R2 or e-Stewards certified recycler.
Repair didn’t go as planned? Try some basic troubleshooting or ask our Answers community for help.

0 Guide Comments

Add Comment

View Statistics:

Past 24 Hours: 0

Past 7 Days: 4

Past 30 Days: 19

All Time: 191