Skip to main content

Free Shipping on Domestic Orders $75+

Atari Lynx Backlight Replacement

Views: 5.7K

View statistics:

Past 24 Hours:
5
Past 7 Days:
25
Past 30 Days:
108
All Time:
5,706
Comments: 2

1 comment on steps, 1 guide comment.

Go to guide comments
Completed: 4

4 people have marked this guide "completed." Will you be next?

Favorites: 1

1 person has favorited (and subscribed to) this guide. Will you be next?

Time Required: No estimate
Difficulty: Difficult
Atari Lynx Backlight Replacement

Introduction

Go to step 1 ↓

Before starting this guide you may need some experience with soldering/ desoldering. If you do not know how, you can learn by clicking the link we put on step 8 (when you have to desolder the backlight).

What you need

Tools

    1. Atari Lynx Backlight Replacement, Atari Lynx: step 1, image 1 of 1
      • Before disassembling your Atari Lynx, be sure the device is powered off.

      • Remove any game in the console by opening the right latch and sliding the game to the right.

      Ask FixBot

      Add Comment

    2. Atari Lynx Backlight Replacement: step 2, image 1 of 1
      • Remove the four 35 mm Phillips #1 screws at each corner of the backside on the Atari Lynx.

      • Pinch the rear panel with your fingers and lift away from the Atari.

      Ask FixBot

      Add Comment

    3. Atari Lynx Backlight Replacement: step 3, image 1 of 1
      • Remove the battery panel by pinching the sides with your fingers and lifting it away from the Atari.

      • Be sure not to tear any wires attached to battery panel.

      Ask FixBot

      Add Comment

    4. Atari Lynx Backlight Replacement: step 4, image 1 of 1
      • Remove the control panel by pinching the sides with your fingers and lifting it away from the Atari.

      • Be sure not to tear the speaker wire while removing the control panel.

      Ask FixBot

      Add Comment

    1. Atari Lynx Backlight Replacement, Backlight: step 5, image 1 of 1
      • Pull out the logic-board.

      • Pull to the sides the four rubber tabs holding in the screen

      Ask FixBot

      Add Comment

    2. Atari Lynx Backlight Replacement: step 6, image 1 of 1
      • Unscrew the two 10 mm screws as shown with a Phillips #0 screwdriver in order to remove the shield behind the backlight.

      Ask FixBot

      Add Comment

    3. Atari Lynx Backlight Replacement: step 7, image 1 of 1
      • Flip over the motherboard and remove the shield behind the backlight.

      Ask FixBot

      Add Comment

    4. Atari Lynx Backlight Replacement: step 8, image 1 of 2 Atari Lynx Backlight Replacement: step 8, image 2 of 2
      • Flip the motherboard back over and desolder the two components that are holding the backlight in place.

      • If you need help with basic desoldering, click here.

      Ask FixBot

      Add Comment

Conclusion

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

4 other people completed this guide.

John Lopez

Member since: 01/27/14

446 Reputation

4 Guides authored

Team

Cal Poly, Team 1-42, Maness Winter 2014 Member of Cal Poly, Team 1-42, Maness Winter 2014

CPSU-MANESS-W14S1G42

5 Members

72 Guides authored

1 Guide Comment

Good instructions but my Atari is different

909 - Reply Share

Add Comment

View Statistics:

Past 24 Hours: 5

Past 7 Days: 25

Past 30 Days: 108

All Time: 5,706