Fix Your Stuff Community Store

Free Shipping on Domestic Orders $75+

Anker Soundcore Motion Boom Plus Case Disassembly

Introduction

Use this guide to access the internal components of an Anker Soundcore Motion Boom Plus.

What you need

  1. Anker Soundcore Motion Boom Plus Case Disassembly, Case: step 1, image 1 of 3 Anker Soundcore Motion Boom Plus Case Disassembly, Case: step 1, image 2 of 3 Anker Soundcore Motion Boom Plus Case Disassembly, Case: step 1, image 3 of 3

    • Insert an opening tool into the seam between the speaker grille and the chassis.

    • Pry the tool around the top, bottom, and sides until the grille fully releases.

    • Apply gentle pressure to avoid damaging the grille.

    • Remove the grille.

    Edit

  2. Anker Soundcore Motion Boom Plus Case Disassembly: step 2, image 1 of 2 Anker Soundcore Motion Boom Plus Case Disassembly: step 2, image 2 of 2

    • Remove the two passive radiators on either side of the device.

    • Avoid pulling too hard or with too much force to prevent breaking the passive radiators.

    Edit

  3. Anker Soundcore Motion Boom Plus Case Disassembly: step 3, image 1 of 2 Anker Soundcore Motion Boom Plus Case Disassembly: step 3, image 2 of 2

    • Remove the sixteen 14 mm Phillips screws, eight on each end of the speaker.

    Edit

  4. Anker Soundcore Motion Boom Plus Case Disassembly: step 4, image 1 of 3 Anker Soundcore Motion Boom Plus Case Disassembly: step 4, image 2 of 3 Anker Soundcore Motion Boom Plus Case Disassembly: step 4, image 3 of 3

    • Gently remove the handle from the device by clicking off the handles from the sides and then pulling it off.

    Edit

  6. Anker Soundcore Motion Boom Plus Case Disassembly: step 5, image 1 of 2 Anker Soundcore Motion Boom Plus Case Disassembly: step 5, image 2 of 2

    • Flip the speaker onto its side and use a spudger to remove the two rubber feet on the bottom of the device.

    Edit

  7. Anker Soundcore Motion Boom Plus Case Disassembly: step 6, image 1 of 2 Anker Soundcore Motion Boom Plus Case Disassembly: step 6, image 2 of 2

    • Remove the eleven 13 mm Philips screws that secure the driver housing.

    Edit

  8. Anker Soundcore Motion Boom Plus Case Disassembly: step 7, image 1 of 2 Anker Soundcore Motion Boom Plus Case Disassembly: step 7, image 2 of 2

    • Remove the two 14 mm Phillips screws located on each side of the handle, near the clip points.

    Edit

  9. Anker Soundcore Motion Boom Plus Case Disassembly: step 8, image 1 of 2 Anker Soundcore Motion Boom Plus Case Disassembly: step 8, image 2 of 2

    • Remove the four 14 mm Philips screws on the top of the device.

    Edit

  10. Anker Soundcore Motion Boom Plus Case Disassembly: step 9, image 1 of 1

    • Insert a spudger into the seam on top of the device.

    • Gently pry the casing open.

    Edit

  11. Anker Soundcore Motion Boom Plus Case Disassembly: step 10, image 1 of 3 Anker Soundcore Motion Boom Plus Case Disassembly: step 10, image 2 of 3 Anker Soundcore Motion Boom Plus Case Disassembly: step 10, image 3 of 3

    • Disconnect each of the three cables by gently pulling the connectors out of their sockets.

    • Do not pull with force. The ribbon cables are fragile and easily break.

    Edit
Conclusion

To reassemble your device, follow these instructions in reverse order.

Author

Connor Bassolino

Member since: 03/29/22

21,444 Reputation

98 Guides authored

Badges: 30

+27 more badges

0 Guide Comments

Add Comment

View Statistics:

Past 24 Hours: 0

Past 7 Days: 4

Past 30 Days: 47

All Time: 342