Hi,

I was wondering whether my glass is broken or the LCD underneath? Touch is working with no issues.

Thank you for help!

⟐ Edited by author May 14, 2021 at 13:54 MST

can the lock for the flex cable be reattached? Does it need to be soldered or a heavy duty glue can fix it? Help please

⟐ Commented April 30, 2020 at 7:39 MST

Will replacing the screen digitizer fix this or is this something else?

I am not a pro, I know almost nothing, so please use laments terms.

Mahalo

After creating a new iCloud account, I checked if everything is working, and everything seemed OK. Powered the thing off and started putting it back together, EMI shields and all that, but when I tried to power it on before pressing the display back in, it stayed black, the backlight was not working.

Checked the L2200 fuse - continuity is there, as well as between the diode leg and connector pins, D8228 seems fine too, 3.8V on one side, 0 on the other, diode testing mode shows 0 in one direction and 2 and change in the other, hard resets and an additional DFU did not help, connectors look ok.

Honestly, I have no idea what else to look at here.

I was ready to throw this thing out when I decided to try and unlock the iCloud, but that work out great and this new issue popped out of nowhere, bummer =(

I really want to figure this out, please help

Oh wow, just figured out, that 2.07V reading in diode test mode is the voltage drop, which for PMEG4010BEA used in the iPad should be around 0.54V, so it’s probably the diode after all, those things are 8 cent a pop, but I’ll need to grab some new tips for my soldering station to swap it ha ha

⟐ Edited by author October 20, 2019 at 17:55 MST

⟐ Commented August 04, 2018 at 14:20 MST

I have an iPad mini in my store, and i really would like to get it running for my customer. we have replaced the Touch panel assembly (With Control I/C) three times now. twice of which under warranty, and the same issue shows up.

Immediately after the repair, the touch functions perfectly fine. there is no issue for about 2 days. after which the touch stops. When we run a hard reset (Home/Power for 15Sec) it works fine again for a couple days, then stops.

(Yes, i HAVE put the tape across the digi and home button flex to stop any shorts on the frame.)

if anyone has had this issue before, please contact me with the way you fixed it.

If there is any known board issue with this problem, i have the tools and skillset to do micro SMT Solder work, so if you could post me an image highlighting what would need to be replaced, ill get started on that.

⟐ Commented November 23, 2017 at 8:09 MST

⟐ Commented January 24, 2016 at 18:31 MST

1) dark black lines covering maybe 1/4 inch at the bottom of the screen.

2) randomly, those black lines start to travel up toward the top of the screen, but if I put pressure on certain spots of the screen, they go back down.

3) in some apps, the lines take over the whole screen and won't go away until I close the app.

All of these problems persist, but the digitizer still seems to work fine in regards to responding to touch. Please help me figure out the problem!

⟐ Commented September 29, 2015 at 15:33 MST

if i connect it to itunes it tries to restore but gives me error 2001 all the time.

do i need to replace some part of the ipad to fix this problem?

please help me :-)

Has anyone seen this before?

Whats the solution?

https://drive.google.com/file/d/0B8uTfOl...

I noticed that there was a previous repair attempt on this device, as some screws were missing on the inside, and the seller confirmed that they had taken it to a shop, but they could not fix the issue. I tried to connect to iTunes, but the device was not recognized, and a hard reset did not work. I disconnected the battery and reconnected it, and it did not change anything. What component would have likely received damage due to a knockoff charger and how would I go about replacing it? If there is another possible cause, what could that be? Thanks.

⟐ Edited June 21, 2015 at 9:04 MST

I own a repair store for about 9 months now, fixed everything that came by from android to iOS. So I'm not a novice in this.

Last week a customer brought to me 3 iPads for repair. 2 iPad minis and an iPad 3. Fixed all 3, however 1 of the iPad minis now shuts off at random times. Pressing the power button does not help. I must Power cycle the device by pressing the power+home buttons. It could stay on for hours with out an issue then all of a sudden.. black. Nothing.

I would really appreciate it if anybody can give me some help on this. Thanks in advance!!

Just wondering what order the layers in the Ipad Mini LCD go in e.g the Diffusers and Reflectors

If you could send me pictures that would be extremely helpful