Thank You

⟐ Commented December 14, 2016 at 11:45 MST

The touchscreen on my iPad is not working. The home button works fine. I have noticed a damaged pin in the fpc connector.

I wanted to ask is replacing FPC connector too advanced for a beginner? I have watched many videos showing how to do it and I feel fairly confident on doing it. Just wanted to make sure.

Any advice would be appreciated. Thanks

here is the picture.

⟐ Answered September 22, 2023 at 3:14 MST

Is that make the lcd no display at all?

I try to check baclight components all work.

Thanks

Here the component that missing.

⟐ Commented December 29, 2017 at 11:00 MST

recently i broke my ipad screen digitizer, craking it. but there was no damage to screen (inner display working fine). I gave it for repair for digitizer replacement and also asked him to put tempered glass protector (this time being very cautious). after the replacement the screen lock function which switches off display and locks ipad if i close lid of my ipad case had stopped working. Nowadays the color reproduction is drastically different. Like the red lotus ios wallpaper which is of red shade is more of pink shade in my ipad.

im afraid i had been cheated to a duplicate screen. has my screen gone bad or something? pls help me out guys

⟐ Commented December 11, 2017 at 22:14 MST

I was missing 3 but solved 2 now I just need to figure out were to jump the pin 9 and I'm done.

Please help!!! @fixlab !!!

⟐ Answered December 15, 2019 at 15:19 MST

⟐ Answer accepted January 09, 2019 at 5:44 MST

⟐ Answered December 22, 2016 at 11:00 MST

I changed my iPad mini 2 battery recently to an unknown manufacturer model and it started rebooting every 2 - 3 minutes.

I purchased then old original battery and the rebooting problem is now gone.

But another problem is I sniffed the battery for some reason :) and found it smells like nail polish remover.

The smell is very light and could be noticed if I sniff the battery itself only, but it worries me.

The battery doesnt have any signs of physical damage.

Two questions so far then:

• Do I have to replace the battery?
• Where to buy good working battery or how to distinguish good one?

Thanks a lot!

⟐ Commented December 04, 2016 at 7:20 MST

I have a problematic Mini 2 - it reboots sporadically, flashing blue for a split second.

The problem is the device is actually assembled from a lot of parts of different devices, so I need to know potetial roots of the problem at least.

Say, could it be wrong battery or software problem or what else?

The only thing I found the issue occurs if to use wrong screw to attach the plate covering LCD etc connectors, but its unlikely... (Im pretty sure I didnt)

Please help how to diagnose.

⟐ Answer accepted October 17, 2016 at 14:06 MST

⟐ Answered July 09, 2015 at 1:36 MST

Plzz give any perfect solution

I m in a big trouble

Plzz help..

1) After replacing both the LCD and digitizer, the ipad was in need of charging. The LCD turns on to display the red battery. Confirms the LCD works.

2) After the boot logo and the ipad charged, the LCD works for a few minutes to display the homescreen, then goes blank.

3) During those few minutes of the LCD working, I tested the digitizer. The home button works, but touch does not.

4) The power button does not respond to turn the ipad display on. Only the home button turns on the display.

5) LCD goes blank. I reconnect the charger to verify if the ipad is dead. It is not as there is a connecting charge sound.

6) After letting the ipad die over a 24hr period, the LCD works again to display the dead-battery logo.

7) I did not disconnect the battery at all during this installation; however, the iPad was completely dead during installation.

Any idea what's going on? This is new to me after years of ipad screen repairs. First time experiencing this.

I have just now tried to use a new digitizer. The problem is still persisting though. LCD works fine. The digitizer touch is not responding at all, home button responds. I made sure to test the power button, volume, and silence switch, they are all unresponsive once the ipad is charged in addition to the inoperable touch feature.

Attached is a photo of my ports.

⟐ Commented September 22, 2023 at 3:20 MST

I've never read a schematic before so I'm a bit clueless...

⟐ Commented March 06, 2023 at 23:23 MST

⟐ Commented March 01, 2019 at 15:26 MST

⟐ Answer accepted October 13, 2018 at 10:08 MST

I have an iPad mini 2 LTE A1490. I need a digitizer with the IC chip and I encountered this item on your store: http://eustore.ifixit.com/en/Parts/iPad-...

Is it compatible with this model? Thanks

⟐ Commented July 10, 2018 at 5:50 MST

Image

The coating is already dry and feels fairly smooth. It only appears along the top of the battery along the edge that's exposed under the LCD shield plate. There's no sign of fluid below the battery or elsewhere in the iPad. This device has been repaired before.

If it's not from the battery, is there anything else in there that might leak? The LCD looks fine. There were no reported battery issues, either.

⟐ Answer edited February 14, 2018 at 23:25 MST

Perform the change of touch glass by a fall. The glass broke. I made the switch and the tablet worked perfectly for one week. But one nigth after loading it ... the tablet stopped working the next morning.

The first option is a reboot ... it did not work. The iPad's touchpad did not work after restart.

I have to add that I replaced a new glass to rule out that it was not crystal failure. I think the error may come from the motherboard.

I took all precautions for repair. I disconnect the battery and all the terminals following the indications of ifixit.

The iPad, It ran for a week perfectly, but stopped working the touchpad. The iPad turns on and can connect to iTunes, but I need the touchpad to unlock it.

Can anybody help me? Anyone have a previous solution?

Thank you so much.

⟐ Answer deleted November 22, 2016 at 17:25 MST

Also need to repair the home button the button looks and moves but the switch is not clicking is there a repair package i can buy for the home button?

⟐ Answered May 31, 2016 at 13:03 MST

⟐ Answered January 04, 2025 at 7:10 MST