I got horizontal lines over the display! During the warranty period they replaced the board ( it blacked out ) and now this is happening. They refused to replace the device saying out of warranty and asked to replace it :-|. They were not even sure that changing the display will fix the issue. I am hesitant to replace the screen as I am better off to buy a new one rather keep repairing the faulty product.

Is there any way to fix it?

Tried
- Reinstall the OS
- External Display = Works fine
- Reseating those 3 cables

Lines kind of flickers, may be some lose cables?

Please help

⟐ Commented May 02, 2026 at 0:54 MST

⟐ Commented January 29, 2022 at 6:20 MST

⟐ Commented July 28, 2023 at 15:46 MST

⟐ Commented November 17, 2023 at 4:04 MST

⟐ Answer accepted September 03, 2022 at 21:14 MST

It is not essential to get this fixed but I would like to if possible. I have tried the eraser method, the Vaseline method, and hand sanitizer. Any ideas?

⟐ Commented November 04, 2022 at 13:19 MST

Just wondering if anyone has been able to remove the cap covers on the hinge, and what the process was like?

Thank you,

Bill

⟐ Answered September 08, 2022 at 19:03 MST

Or not (as I suspect) as the aluminum chin and the whole glass and display are meld and integrated into one?

Thanks

⟐ Answer accepted September 04, 2022 at 14:24 MST

⟐ Answer accepted September 04, 2022 at 14:23 MST

I wonder if anyone can help me with an issue I am encountering following the installation of a new logic board. The original logic board had failed with no power to the iMac. I purchased a new sealed logic board from a third-party reseller and completed the insulation as per the self-repair instructions. When I turn the iMac on I am presented with the black screen showing an exclamation mark and the restore URL on it. When I try to restore the via usb-c and with my M2 MacBook Air and using DFU, I get the iMac to turn on and start the restore but after few minutes I get the following error messages;

The Mac "Mac" could not be restored. An unknown error occurred (53). 0634.0035

&

The System cannot be restored on this device.

The operation couldn't be completed.

(AMRestoreErrorDomain error 53 - Failed to handle message type StatusMsg (FDR failure)) [AMRestoreErrorDomain - 0x35

(53)]

Has anyone encountered this before or know the possible issue?

Thanks

⟐ Commented August 08, 2025 at 19:42 MST

While perusing the several installation instructions, I might have a blade SSD on the control board (unconfirmed) that is part of the"Fusion" system

Will I be able to just replace the HDD with the SSD and format and install the OS as usual and not deal with the Blade SSD, or ????

Thanks in advance for any help,

Richard

About this Mac screenshot:

Bottom of base showing EMC 2544:

⟐ Commented January 23, 2024 at 20:37 MST

⟐ Answered April 26, 2023 at 15:06 MST

I going to buy an iMac ‘24 and I thinking to travel with him. I was wondering how I can remove the stand to have more space?

Thank you

Sasha

⟐ Answer edited April 01, 2023 at 12:23 MST

⟐ Answer edited March 15, 2023 at 19:06 MST

⟐ Answer accepted September 04, 2022 at 14:23 MST

But I want to know where the photoresistor, truetone sensor located.

⟐ Commented July 07, 2021 at 4:02 MST

⟐ Edited March 04, 2024 at 12:00 MST

This is my cousin's iMac. She told me she was using it one day and heard a loud pop and then the iMac lost power and it would not turn on any more. I was unsure if the problem might be the very expensive AC adapter or the computer itself so I took the computer to a Mac store in a nearby town. They tried plugging a known good AC adapter in to the iMac but it still did not turn on so it seems the iMac is the problem.

Today I took the screen off to have a look at the circuit boards inside to check if there might be something obviously damaged like an exploded capacitor. So far I've seen only one side of the two boards but I don't see anything wrong yet.

I read in another thread that there may be some diagnostic LEDs on the board which may give me some hints about the status of the computer. I tried plugging in the AC adapter, with the screen off, but I did not see any LEDs light up. I did notice there is a tiny button on the main circuit board and it may have three tiny LEDs next to it. I thought about pressing the button to see what would happen but I'd rather not do that unless I know exactly what that button is supposed to do. What does it do?

Should I proceed to disconnect the cables from the main circuit board and take it out to have a look at the backside?

⟐ Edited March 16, 2026 at 21:47 MST

⟐ Answer edited February 11, 2026 at 10:52 MST

⟐ Answered February 11, 2026 at 6:13 MST