iFixit - Answers With Device "Table Saw"

Makita Table Saw 2708 2010: Why is the blade hitting the table when making a 45 degree

Sat, 07 Mar 2026 17:55:35 -0700

The blade is hitting the table on 45 degrees cuts

⟐ Commented March 07, 2026 at 17:55 MST

Delta Table Saw 36540 TYPE 1 2014: Trying to identify a 1 1/2" pin I found beneath the machine

Fri, 20 Feb 2026 22:10:46 -0700

I was using the saw. I moved the saw and in the saw dust beneath the machine I found a 1 1/2" pin with a threaded brass head. Is this a saw part ?

⟐ Commented February 20, 2026 at 22:10 MST

Dewalt Table Saw DW745 TYPE 1 2011: How do I repair a motor?

Sun, 01 Feb 2026 13:21:32 -0700

My motor stopped. it has electricity and the brushes are good but before it quit, for a few days it acted like they were loosing contact: poor startup. How do I remove the motor casing to look inside?

⟐ Answered February 01, 2026 at 13:21 MST

Craftsman Table Saw 137218072 2017: Missing the table guide

Thu, 29 Jan 2026 16:09:57 -0700

I am looking for the guide the slides forward and backwards on the table model 137.248830

Porter Cable Table Saw PCB220TS 2012: blade height hard to adjust

Sun, 18 Jan 2026 04:48:37 -0700

how do you fix blade that is hard to raise?

Ryobi Table Saw BTS20R 2006: Loose motor on my ryobi table saw

Wed, 31 Dec 2025 12:52:24 -0700

Motor was loose. Took it apart and found the 4 screws that attached the plate to the motor to be very tight however the motor was still loose is there a spacer or bushing that is missing? I hate to get rid of it but can’t find a way to get it tight.

Ridgid Table Saw R45101 2012: On off switch smokes

Fri, 04 Jul 2025 09:01:42 -0700

Hasn’t been used for a while is plugged into 20amp plug with 12 gauge extension cord. Motor started as usual and stepped up to full rpm. Made 1 cut ok. Switched off next cut turned on stepped up then quit. Went to flip switch off and wispy smoke was coming out of switch. Unplugged and here I am

⟐ Commented July 04, 2025 at 9:01 MST

Bosch Table Saw GTS1031 2011: The bevel lock broke?

Sun, 22 Jun 2025 10:06:54 -0700

Either some part of the bevel lock has broken or just loosened. When trying to tighten it I felt it give way, rotate too far and now it doesn't tighten to hold the blade at any angle. Seems there is a hex bolt in the base of the handle but it's hard to see and I can't get a hex wrench to fit in it blind. Anyone have experience with the bevel lock?

Dewalt Table Saw DW744 TYPE 1 2012: How to replace the clamp for the slide #11

Sat, 14 Jun 2025 12:05:01 -0700

How to replace the clamp #11

⟐ Commented June 14, 2025 at 12:05 MST

Craftsman Table Saw 137218072 2017: Table saw stopped working

Fri, 16 May 2025 19:34:19 -0700

This Craftsman saw has not been used in four plus years sitting in a shed. I turned it on with an extension cord and it fired up for about 2 seconds I unplugged extension cord I tried to plug it back in and it will not turn on. I know there's a reset button and I try to push it but it won't work. Any suggestions

⟐ Answer edited May 16, 2025 at 19:34 MST

Craftsman Table Saw 31521806 2015: What is the correct wiring diagram for model 315.218060

Tue, 06 May 2025 22:59:11 -0700

what is the correct wiring for model 315.218060 power switch

⟐ Answered May 06, 2025 at 22:59 MST

Craftsman Table Saw 31522839 2017: Drive Belt install instruction

Sat, 18 Jan 2025 07:47:36 -0700

Help on adjusting the Drive Belt.

⟐ Commented January 18, 2025 at 7:47 MST

Craftsman Table Saw 13722194 2015: Are 137 series table saw parts compatible?

Tue, 03 Sep 2024 10:57:36 -0700

I have a 137.221940 craftsman table saw without any fence or blade guard assy. I have had zero luck finding in parts the match this table saw. Does anyone know if the other 137 series saw blade guard or fence work ?

⟐ Answer edited September 03, 2024 at 10:57 MST

Skil Table Saw 3310 F 012 331 0 2017: I cannot raise sawblade

Sat, 30 Mar 2024 08:20:49 -0700

I am using front wheel to raise saw blade but it will not work. some part mays be missing.

Table Saw: Finding a replacement rip fence?

Sun, 17 Dec 2023 12:18:54 -0700

TL;DR: Ripped some wood, blade contacted the rip fence because the cut was thin enough that I had to remove the blade guard. At least I caught it in time but this scored it pretty good.

I did a chat support with Vevor, and they said they would send me an email to buy the part... It's been a pain. They do not have a site I can just pay for it and get a replacement.

Does anyone know an alternative source for the part in the meantime while I try and get them to work with me? Better yet, a part number.

⟐ Commented December 17, 2023 at 12:18 MST

Dewalt Table Saw: Has anyone changed the motor assembly to run a DWE7491 in Europe?

Sun, 05 Nov 2023 16:22:04 -0700

Hello,

I have a DWE7491 that I love. I’m planning to move to Europe in a couple of years. I see that there are dewalt specific spare part for the motor to run in Europe. I was wondering if anyone had experience changing the motor assembly themselves ?

Thanks

Herve

Craftsman Table Saw 1372181 2017: Table saw shut off

Tue, 26 Sep 2023 00:10:29 -0700

It was given to me by a close friend. All I had to do was build a base around the broken base. So I did. He said he messed with the wiring one day and now it doesn't turn on. I'm needing wiring diagram