A couple of services for unlocking locked devices rejected me because my device doesn't prompt for unlock code.

When i insert non supported sim card the device reboots and that's it, no prompt for entering unlock code, nor when i inserted another sim.

I tried with force USSD code to show me the unlock menu but that doesn't work either.

⟐ Commented April 25, 2025 at 8:52 MST

⟐ Answer deleted September 29, 2021 at 7:52 MST

I was wondering if it is possible to change the power button of My sony xperia M2 ?

It is stuck, someties it works, sometimes it won’t and I have to use the camera button to unlock the phone.

Someone knows if one can replace it ?

PLEASE HELP ME

I tried waiting for the battery to run out. The phone slightly overheated, then I charged it again and the moment it had a little charge, it started doing this again. The On/Off button isn't stuck or anything alike.

What do I do?

⟐ Commented October 12, 2018 at 13:59 MST

Sony Xperia M2 - Dead Unit.

Device status & measurements :

The fault is Phone is not charging, USB Power ( 5V, 10-20 mA) Battery Charging voltage 1.1 - 4.1V, current fluctuating.

Note : This is liquid damaged device

Observations & tests

• TH voltage is 1.2V it seems OK

• There is no BAT EN signal 0.6V

* Phone can be power on when given the BAT+ - to with external power supply

• When plug the battery connector 0V at battery terminals. that's mean Battery Disable itself
• When unplug the battery and can be get measurement 3.7V
• Checked with new battery, same result observed. - Battery is OK

If any idea please comment. Thank you for your time. in simple i need to enable BAT EN signal or need a way to bypass. or Please help to find schematic diagram for D2303

⟐ Commented July 09, 2018 at 13:22 MST

my device(Xperia m2 dual) after unbrick, don't work sim card slot 2nd.

How to fix this problem?

⟐ Answered February 21, 2018 at 6:08 MST

⟐ Answer accepted August 30, 2017 at 6:45 MST

when he gave it to me he said to me that water has been spilled(a few months ago) and nothing worked.

i gave it to a repair shop and they said that they cant repair it but after pressing a button at home after a few hours sound began to work. and the display too can be seen with a torch(no backlight).buttons too can be pressed.torch too works.

yersterday i noticed that when pressing the power button (to see lock screen) the backlight works well(as normal) for about half a second and dims again.

anyway to fix this?.

help is highly appreciated!

⟐ Answer accepted May 09, 2017 at 5:04 MST

⟐ Answer deleted April 26, 2017 at 1:51 MST

After a sock the the vibration motor stopped, and it works for a small time after clicking with my fingers on the mobile and then it stops until i click again.

and the loud speaker is working but it's volume is too much low, i think one of the channels ( right or left) have just stopped working.

can it be repaired without replacing the motor/speaker ? (for example , the sock made the connectors of the motor disconnect , so reconnect them again... )

⟐ Answer edited February 23, 2017 at 8:03 MST

I did a factory reset and there is still the same problem.

Do you think it's a camera hardware problem or logic board?

Thanks!

⟐ Commented January 19, 2017 at 1:29 MST

Please Help!

I wanted to flash a custom rom CM 12.1 for my M2. I forgot to update the bootloader and it said patching system image unconditionally... and it froze then. I let the battery run out and it shut down. When i try to power it up it just stays on the sony screen and i cant do anything. Its not a bootloop its just a frozen screen.

⟐ Commented August 11, 2016 at 10:22 MST