iFixit - Answers With Device "Samsung WF42h5600ap a2"

Samsung WF42h5600ap a2: Hot water continues to run

Thu, 22 Jan 2026 08:40:54 -0700

Hot water will not shut off even when washer is off

⟐ Answer accepted January 22, 2026 at 8:40 MST

Samsung WF42h5600ap a2: Washer stops after trying to move through cycle with no error codes

Fri, 24 Feb 2023 14:21:13 -0700

The washer sounds like it’s trying to move forward but does not. I’ve tried running rinse and spin only cycles but it does not move forward and after several minutes the door unlocks and stops the cycle. In speaking with Samsung they were of little help. I tried turning off the switch to power the machine in the electric panel and thought it had worked but it only moved forward a bit more and then stopped again. No obstructions in the drain or drain pump and I can move the drum manually. Any help is appreciated!

Samsung WF42h5600ap a2: Why error H3 in samsung washing?

Tue, 14 Feb 2023 02:15:10 -0700

why error H3 apear in samsung washing mashin?

Samsung WF42h5600ap a2: Washer Turns Itself Off Model WF42H5600AP/A2

Thu, 28 Dec 2023 09:32:58 -0700

Washer Turns Itself Off - Model WF42H5600AP/A2

My washer will power on initially when I hit the power button, but the user interface display will only stay on for about five seconds and then I will hear a click and the unit turns off by itself. When I try the power button again the next few times, it will not power up (I hear it click then click off again instantly), then eventually after hitting the power button enough times, it will click on and the user interface display will light up for a few brief seconds again, before powering off again by itself. Even after it powers itself off, the green lights on the Main and Inverter PCBs continue to flash.

I checked and have 120V going to the filter and out of the filter. 120V goes to the Main PCB and Inverter PCB, and both of these have blinking green lights on them. I also checked the power coming out of the Main PCB to the front user interface PCB and have the correct 5V and 12V to ground.

Would you expect this to be an issue with the Main PCB, User Interface PCB, or anything else?

I’ve looked at all circuit boards and don’t see any visible burns, damages, or loose connections. I’ve also tested all the capacitors on the Main PCB and user interface PCB - all tested fine. Wiring harness appears to test fine with a continuity test as well.

⟐ Edited December 28, 2023 at 9:32 MST

Samsung WF42h5600ap a2: Samsung washer power will not stay on

Thu, 28 Dec 2023 09:31:15 -0700

Washer model:wf42h5000aw/a2

After i pressed power button, the panel light blinked for one second. Then lights went off. Nothing happened after.

I purchased a new electronic control board. Same thing happened.

I also tested it on electronic control panel without front face plastic board: i pressed power button, then immediately pressed pause/play button, 1 out of 5 times, the power stayed on and washer was able to complete a 59 min wash and spin cycle. HoweverIf i choose other cycle (delicate wash), the power went off again.

I thought it is a wire adapter connection issue and checked all wires..no problems there ..otherwise washer could not run 59min wash cycle.

Please lend a hand. Thanks

⟐ Edited December 28, 2023 at 9:31 MST

Samsung WF42h5600ap a2: Samsung WF42H5200AW washing machine door issues

Thu, 28 Dec 2023 09:58:08 -0700

squeeking in cycle and door won’t open until new cycle choices display

⟐ Edited December 28, 2023 at 9:58 MST