iFixit - Answers With Device "Power Screwdriver"

DeWalt DW920: Why is my drill not charging?

Fri, 03 Apr 2026 05:49:42 -0700

When i place the battery pack on the charging station, the battery not charge.

⟐ Commented April 03, 2026 at 5:49 MST

Dewalt Corded Screwdriver DW257 TYPE 4 2011: Why doesn't the pin holder lock into the clutch assembly anymore?

Sat, 16 Aug 2025 08:04:37 -0700

When I slide the pin holder into the clutch assembly, it doesn't lock anymore, so it comes out all the time. Anything wrong with the ball that is supposed to go into the bit holder groove and lock it in place?

Black and Decker 9074 Type 4: How do I remove/replace batteries in BLACK and DECKER

Tue, 04 Feb 2025 09:16:11 -0700

I own a BLACK and DECKER PLUG-IN RE-CHARGEABLE HAND HELD SCREWDRIVER

DP240 TYPE 2.

IT would not charge/ or hold a charge in the end. Found the replacement batteries at BATTERIES PLUS BULBS, the tech said the company would not allow them to un-solder

the batteries , so I purchased the strapped batteries and will install them myself but I need help in safely removing the old batteries and installing them without damaging the circuit board or its components.

WIllie E Brown

⟐ Commented February 04, 2025 at 9:16 MST

Black and Decker LI2000: BLACK+DECKER Li2000 REPLACEMENT BITS

Sun, 17 Nov 2024 20:10:15 -0700

Where can I order replacement bits for the Black+Decker Li2000 online, and what part or product number is associated with them?

⟐ Commented November 17, 2024 at 20:10 MST

Durofix RV332 Cordless Li-ion Screwdriver: Wiring diagram for battery,trigger and motor.

Mon, 16 Sep 2024 08:36:43 -0700

Am swapping batteries and need to know the correct wire placement when i solder them back to the board..

⟐ Answer accepted September 16, 2024 at 8:36 MST

Black and Decker LI4000: Where can I buy the charging bay for my drill

Fri, 24 Nov 2023 08:03:06 -0700

How do i replace my charging bay for my black and decker cordless L14000

⟐ Answer edited November 24, 2023 at 8:03 MST

Black and Decker Pivot Plus PD600: Forward but not reverse?

Mon, 20 Jun 2022 11:26:33 -0700

Worked fine last night, but today it runs fine screwing in - but in reverse, it does not work at all. Has this happened to anyone else? If so what did you do? Is it just broken and I need to send it in for warranty work? Or is there something I need to do that I am overlooking?

⟐ Answered June 20, 2022 at 11:26 MST

Durofix RV332 Cordless Li-ion Screwdriver: model RV332 4V 200min. Need power adapter!

Sun, 17 Oct 2021 16:06:25 -0700

Have model RV332 4V 200min. Need power adapter!

⟐ Answered October 17, 2021 at 16:06 MST

Durofix RV332 Cordless Li-ion Screwdriver: Need a new power adapter.

Sun, 17 Oct 2021 13:16:37 -0700

What is the voltage output and MA rating of the power adapter?

⟐ Answer deleted October 17, 2021 at 13:16 MST

Black and Decker Pivot Plus PD600: Drill bits for Black & Decker Pivot Plus PD600?

Thu, 10 Dec 2020 12:30:28 -0700

Where can I purchase the drill bits for my Black & Decker Pivot Plus PD600?

⟐ Answer deleted December 10, 2020 at 12:30 MST

Black and Decker LI2000: LI2000 internal parts schematic

Sun, 08 Sep 2019 15:54:00 -0700

I took apart a LI2000 screwdriver and can’t get it back together correctly. Is there an internal parts schematic available?

⟐ Answered September 08, 2019 at 15:54 MST

DeWalt DW920: How do I disengage the auto chuck release.

Tue, 01 Jan 2019 13:05:04 -0700

Doing work on multi layer conveyor systems accessing control panels. Lost the bit and and lost my backup didn't have another backup other than a screwdriver which I resorted to. Bits fell 5 stories never to be seen gain. The slightest bump on the chuck ejects the bit - Very poor design.

I'm committed to the unit - too late to return it. So I have electrical tape wrapped several time around the chuck forced in between the chuck and unit to keep chuck from moving. Sure hope I don't have to replace the bit or bit holder

⟐ Answered January 01, 2019 at 13:05 MST

Black and Decker 9074 Type 4: reinsert clip in 9074 screwdriver

Fri, 11 May 2018 09:16:20 -0700

How do I put the clip holding the transmission to the body back in the screwdriver? It seems to get "stuck" 3/4 of the way in and I'm uncertain how much force I should use to put it back in.

⟐ Answer accepted May 11, 2018 at 9:16 MST

Durofix RV332 Cordless Li-ion Screwdriver: replacement drill bits and drivers

Fri, 16 Feb 2018 06:09:43 -0700

my grandchildren have lost the drill bits and drivers for my durofix RV332 cordless Li-ion screwdriver. Are replacements available?

⟐ Answer accepted February 16, 2018 at 6:09 MST

Black and Decker 9074 Type 4: Model 7014 electric black and decker variable drill

Sun, 04 Feb 2018 23:42:04 -0700

I read the manual and still do not know how to reverse the drill direction. Thx.

⟐ Answer unaccepted February 04, 2018 at 23:42 MST

Black and Decker LI4000: Why will my screwdriver not charge when plugged in?

Sun, 26 Feb 2017 00:38:40 -0700

My rechargeable screwdriver will not charge when it is placed in the charging bay. The LED light is not on.

⟐ Commented February 26, 2017 at 0:38 MST

Durofix RV332 Cordless Li-ion Screwdriver: What is the polarity of this screwdriver and positive or negative

Sat, 18 Feb 2017 20:21:04 -0700

what is the polarity of this screw driver...a positive or negative...lost the adapter and purchase a universal ac adapter...butI need the polarity inorder to recharge...can you help????

Thanks

⟐ Answer accepted February 18, 2017 at 20:21 MST

DeWalt DW920: Why cant I power the drill?

Thu, 07 Apr 2016 00:21:03 -0700

when i hit the trigger nothing happens but the battery station says that the battery is fully charged.

⟐ Answer edited April 07, 2016 at 0:21 MST

Black and Decker LI4000: Why will the screwdriver not turn when I pull the trigger?

Thu, 18 Feb 2016 21:31:57 -0700

The screwdriver will not turn when I pull the trigger. The work area LED is coming on.

⟐ Answer accepted February 18, 2016 at 21:31 MST

Black and Decker LI4000: Why will my screwdriver not drive the screw all the way in?

Thu, 18 Feb 2016 18:34:28 -0700

The screwdriver does not drive the screw flush with the desired surface.

⟐ Answer accepted February 18, 2016 at 18:34 MST