⟐ Commented July 18, 2026 at 10:30 MST

⟐ Commented July 12, 2026 at 23:37 MST

I put in new tmr sticks in my duelsense v2 controller. I accidentally stripped out the through hole for the middle pin on the right of the board but it came out whole so I took it and pushed it back in the hole. Now after fully soldering in the tmr stick that one is hard stuck to the left when trying to calibrate it.

⟐ Commented June 30, 2026 at 9:15 MST

⟐ Commented June 26, 2026 at 6:53 MST

⟐ Commented May 31, 2026 at 9:08 MST

Translation:

It lights up, but when I try to use it on my laptop, it doesn't work.

⟐ Commented May 22, 2026 at 1:08 MST

help my joystick aint stick drifting its more like Tokyo drifting, I have attached media of one.

my main controller had trigger issues which was giving a response when I wasn't even using the triggers so I used the same conductive film but switched the hardware of my other controller's pcb board which wasnt turning on and then the trigger issue was resolved but the that Tokyo drift issue came up so I guess the board is the issue but I'm not sure

⟐ Edited April 30, 2026 at 4:47 MST

Hi everyone,
I have a standard PS5 DualSense (not the Edge) and I need to replace the white 6-pin mic connector on the mainboard.
I found a replacement part that is listed for the DualSense Edge.
Does anyone know if the white 6-pin socket on the Edge is the same (same pitch and pinout) as the one on the standard DualSense?
Has anyone tried this?
https://modchip.gr/gaming/antallaktika-p...

⟐ Edited by author February 26, 2026 at 6:50 MST

⟐ Commented February 17, 2026 at 1:27 MST

I’m working on a PS5 DualSense (BDM-030) where I replaced both joysticks with GuliKit TMR modules. During removal of the original left stick, the LSX (left stick X-axis) trace was damaged.

Current symptoms:

Left stick only registers movement to the left, top-left, and bottom-left.
VCC is present (~1.8V).
Ground has continuity.
The LSX signal (middle pin) does not show continuity to any nearby components, so I believe the signal trace is broken.

I previously attempted a jumper to VCC by mistake, removed it, and confirmed the issue is specifically the LSX signal path.
I’m trying to locate the correct series resistor or via for the LSX signal on the BDM-030 board so I can run a proper jumper to the MCU side of the circuit.

Does anyone know:

The exact resistor designation for LSX on BDM-030?
A confirmed via location for that signal line?
A known safe jumper point for this repair?

Any boardview reference or photo guidance would be greatly appreciated.

Thanks in advance.
-Zeek

⟐ Edited by author January 31, 2026 at 14:51 MST

⟐ Commented November 29, 2025 at 8:27 MST

⟐ Commented November 08, 2025 at 17:02 MST

My headphone jack on my controller still isn't working even though I had replaced it with a new one. Not entirely sure what I did wrong, as I bought a hot air rework station specifically for this as that seemed like the safest option when it came to removing and replacing the jack.

⟐ Commented October 12, 2025 at 2:18 MST

I need some help with tracing the circuit path (pinout / routing) for the analog stick potentiometer. If anyone has a boardview, schematic, or repair experience with this, I’d really appreciate your guidance.

⟐ Commented September 22, 2025 at 3:02 MST

⟐ Edited September 13, 2025 at 17:49 MST