I have a OnePlus Nord 2 DN2103 with a broken screen. ifixit and the other main sites do not sell a replacement screen because it is too old.

When i look on Amazon or Ebay i have no idea how to figure out what is legit and what is not legit. The prices vary significatly and I dont want to get ripped off.

I have used ifixit to replace and iphone screen before, so have all the tools and found it simple enough that i thought i could do the same with this oneplus nord.

Does anyone have suggestions for what to look for, or maybe a site that could source one for me? Or would it be the case that nothing will be worth it, and I should just give up on this idea?

Any advice or tips are welcome :D

⟐ Answered January 09, 2025 at 11:43 MST

⟐ Answered December 12, 2024 at 14:18 MST

⟐ Commented November 19, 2024 at 0:40 MST

⟐ Answered October 25, 2024 at 1:15 MST

What's wrong?

⟐ Commented August 28, 2023 at 2:36 MST

⟐ Answered July 24, 2023 at 0:15 MST

I putting a new tempered glass cover on my phone, when the screen popped out. The screen was still working, however. No problem, I will need to just glue it on after. Then, after putting on a new tempered glass the screen wasn't turning on any more! Does anyone know what could cause this? The phone still seems to be working, when I hold the power buttons it vibrates a bit, but the screen is completely black.

I removed the back panel, and it seems like the rear connection is fine. Does anyone have any ideas about what could be broken? I would rather not get a new screen, as I may as well get a new phone. I am honestly more annoyed than anything that I seem to have broken my phone, and I would like to know what it could have been. Did I accidentally pull too hard on anything? Thank you!

⟐ Answered July 03, 2023 at 11:49 MST

 Well Hello There,

I'm still fairly new to doing phone repairs and have been really successful so far.

I just have 1 struggle I can't seem to get the hang of and that's those pesky coaxial antenna cables..

I have such a hard time reconnecting those things because they are so small and fragile.

Sometimes I might even destroy 1 or 2 of them before getting 1 to properly connect.

Can anyone share a secret or a few tips on how to reconnect these things fairly easily and quickly

Because I don't wanna have to buy a few OEM spares for every phone I work on

More importantly

A simple repair that should only take 30 minutes would actually only 30 minutes and not 1hr and 30 minutes due to me fighting with those cables for an hour

Thanks In Advance

⟐ Answered September 26, 2022 at 7:27 MST

⟐ Commented August 16, 2022 at 7:38 MST

⟐ Answer accepted August 09, 2022 at 2:17 MST

When I plug my new screen for testing, the phone won't turn on. The only input I get any sort of response from, is when I hold the power and volume up button for 10 seconds. This makes the phone do a quick lil vibration and that's all.

I don't think the new screen is the issue. Has the battery been discharged? If it has, the phone wouldn't vibrate at all, right? I don't see what else even could be the problem. The phone worked prior to disassembly besides the, by then, black screen and a few working pixels near one of the edges. Speaker worked fine and google assistant was responsive.

I had the charger plugged in for 4-5 hours, yet nothing changed. The battery pin is plugged in. The daughterboard and speaker thing are still disconnected but the screen should still work without them, right? Sim/SD card tray are unplugged too if that's important. What could the issue be here?

⟐ Commented July 27, 2022 at 18:49 MST

I'm suspecting that I have a faulty USB-C port on my Nord, or at least some of the connections of the port.

Recently my phone started charging really slow, even with the Warp-charger, I have ruled out cable issue and power adapter issue as I've tried different ones. (Of course also checked for software related issues, but no luck).

Hence my suspiscion towards the port itself, would it be possible to have a guide showing this uploaded?

Or if anyone have experienced similar issue and resolved it differently, please let me know.

Cheers,

Markus W

⟐ Edited by author April 04, 2022 at 5:32 MST

⟐ Answered February 15, 2022 at 15:42 MST

I was about to take my OnePlus Nord back cover off to test something with my vibration motor and realised that I might have to replace the adhesive when putting things back together. I am new to taking phones apart that use glue, so I wasn’t sure how this would work, especially since the Nord doesn’t require a heatgun to remove the back.

Do I need to replace the original adhesive before putting the rear cover back on, or does it fit back together without doing that using other connectors or possibly the original adhesive?

thanks,

Yannick

⟐ Answer unaccepted January 07, 2022 at 13:21 MST