iFixit - Answers With Device "Ninja NJ600"

Ninja NJ600: Why are the blender blades not rotating?

Sat, 02 Nov 2024 15:30:30 -0700

The blender is plugged in, powered up, and properly assembled. However, when I try to run the blender with food in it, the blades do not rotate.

⟐ Commented November 02, 2024 at 15:30 MST

Ninja NJ600: Why will my NJ600 not turn on?

Sun, 29 Sep 2019 09:22:35 -0700

I have the blender plugged in, and have made sure that there is no break in the power cord. The power light will not turn on, and the blender does not run when I try any of the buttons.

⟐ Commented September 29, 2019 at 9:22 MST

Ninja NJ600: Where can I buy the ciurcuit board?

Mon, 20 Jun 2016 18:54:09 -0700

I have a ninja BL780 and I need to buy de circuit board. Where can I buy?

⟐ Answered June 20, 2016 at 18:54 MST

Ninja NJ600: Why is my food not being blended properly?

Thu, 21 May 2015 08:17:55 -0700

My blender seems to be properly powered on, but my food does not have the right consistency.

⟐ Answer accepted May 21, 2015 at 8:17 MST

Ninja NJ600: blender won't lock onto base

Mon, 02 Jul 2018 21:49:16 -0700

My Ninja blender won't lock onto the bottom of the base. It usually sits straight down on base with corners unmatched then you turn it a quarter of a turn to lock it in place. It won't even sit on the base straight down. It has no broken pieces or any particles of anything in the way to keep it from lining up. I usually use the small cup for everything, but I need the big blender today. Did I forget about some safety feature or something?

⟐ Answer deleted July 02, 2018 at 21:49 MST

Ninja NJ600: The blender sparked and stopped working

Thu, 22 Aug 2019 07:42:11 -0700

I bought the Ninja NJ600CO in June 2019 in USA and brought it to India. I knew that I would need a step-down converter to reduce the power supply to 110 volts because in India it is 220 volts. So I used a step-down converter to bring down the supply to 110 volts. The blender said it was a 1000 watts so I made sure to buy a heavy duty converter that could support the wattage till 1600 watts. However, as I plugged it in and switched it on, the blender sparked, made a jolty noise and conked off. I immediately disconnected the power supply. I’m not sure what to do next, I’m scared to plug it in again because I don’t want to do more damage. It’s brand new and I’m in India and can’t even take it back. Would be great if it could be repaired and ideally modified to suit 220 volts power supply. Please help, thanks!

⟐ Answer edited August 22, 2019 at 7:42 MST

Ninja NJ600: My NJ600 only runs on HI (3) speed..

Sun, 12 Jan 2025 10:01:54 -0700

Pushing any speed selection, 1, 2 or 3 runs the blender on the highest speed (3) only. Anybody else figured how to fix this. Just using the Pulse for now...

Ninja NJ600: How can I find a replacement female coupling?

Tue, 23 Jul 2019 18:28:42 -0700

The coupling blade with the 6 rubber finds that fits into the base with the same fine has burnt out. I cannot seem to find just that replacement part.

Ninja NJ600: Where can I find PC Board or parts values?

Tue, 24 Jul 2018 08:48:10 -0700

need circuit board for this blender, or ZNR1 part value, also TA1, identification value.