Can anyone help?

user guide or repair guide also helps.

Thank you.

⟐ Answer deleted January 30, 2017 at 0:49 MST

Are PCIe SSDs also supported?

⟐ Commented January 09, 2020 at 15:21 MST

I read The read/write speeds of the Studio's hybrid drive were around 200-300mbps and the Surface Book laptop was 1.6+gbps, which makes the laptop hard drive 5 times faster than the new Studio.

⟐ Answered June 06, 2022 at 2:00 MST

⟐ Commented April 23, 2024 at 3:15 MST

⟐ Commented November 13, 2021 at 4:55 MST

⟐ Answer accepted October 07, 2021 at 15:53 MST

⟐ Answer accepted March 27, 2021 at 9:02 MST

I appreciate all the writeups on this, made it a lot easier to get done.

Everything went fine, hardware wise. Drives both replaced, and both visible to windows install, and no smoke.

I CAN install windows, however when I try to update the iastora Raid driver, I either get a bluescreen, or it hangs on reboot, and never comes back. Same happens when I try to run the latest Surface studio driver pack, it just hangs at boot, where the dots circle.

I posted a bit more detail on microsoft site, but it doesn’t look like they support this.

https://answers.microsoft.com/en-us/surf...

Has anyone tried this recently, or maybe has some ideas on getting the drivers setup right?

Thank you,

Jim

⟐ Answered January 09, 2020 at 14:56 MST

⟐ Answered March 27, 2026 at 11:53 MST

⟐ Commented April 26, 2024 at 22:41 MST

First, thanks for the website. Without this i would not have considered cracking open the old Studio. I've replaced both of the SSDs, and will also replace the fans, one of which was locking up, even after blowing 8 years of dust out of it.

I'm having a very hard time with the tiny little fan connectors. Don't want to rip the cables, even though I have new fans to put in.

How exactly does one release the connector? What does one press on, or push, or prod? I've got my trusty spludger here, but have tried pushing on the ends, the sides, and tried jiggling the connectors, but nothing seems to come out. I half-expected to press the "right thing", and hear a satisfying click -- nothing.

Also, the audio connector came out from the board instead of the inline connector, which I also couldn't figure out how to release.

Anyway, enough whining... I hope someone sees this and takes pity. Also, though I don't wish any ill will, I hope the answer helps someone else out.

⟐ Answered November 11, 2023 at 21:04 MST

due to a crash from the table (don't ask... unlucky combination of kids and cats) my front glas is broken and I'm wondering where to get a spare one. Any ideas?
I already checked https://support.microsoft.com/en-us/surf... but it seems like they only offer "offical" repacement-parts for newer devices....

Thanks a lot in advance,

Nik

⟐ Answer edited February 28, 2023 at 6:43 MST

I just watch the whole teardown of MS surface studio. It is amazing.

I am going to international exchange to Japan for a while and i would like to bring my surface studio with me. So I would like to learn how to separate the monitor and dock in order to package the monitor well for the flight.

⟐ Answer accepted December 18, 2020 at 11:22 MST

I am thinking if I can remove everything in the base and custom build the PC (by increasing the thickness of the base). I watched the teardown. Do anyone know what kind of connector is used for the monitor? And what kind of additional/unusual ports/adapters are there in studio motherboard

⟐ Answer accepted November 12, 2020 at 5:09 MST

⟐ Commented August 18, 2019 at 20:37 MST

Many thanks

David Phillips

⟐ Answer accepted November 28, 2018 at 10:36 MST

⟐ Commented July 23, 2018 at 11:47 MST

⟐ Commented April 27, 2018 at 10:41 MST

⟐ Answered March 10, 2018 at 1:28 MST