During my research I found a number of complaints about the on/off switch failing and the ability of the groomer to accept a charge.

Initially the unit I bought worked well and had no problem with either the switch or charging. However, after owning it for about a year with light use, both of these problems emerged and now I can only turn it off by inserting the plug in the recharging jack.

In order to repair/troubleshoot the problems I need to know how to disassemble the razor/groomer.

⟐ Commented November 03, 2025 at 6:17 MST

Mine has just stopped taking charge.

Oh, the on button is broken as well...

EDIT:

It's the Theragun Elite (https://www.therabody.com/uk/en-gb/elite...) from a few years back - there is no swappable battery. Will post pictures tomorrow.

EDIT 31/12/2024

Still not completely given up and still massively encouraged and grateful for commenters so far - thank you.

Found this page that shows the battery in question but I can't read the langauge so no idea...I can't find a replacement battery, sadly.

10.8V锂电池组，6V电源适配器，数显光纤放大器 - 〓器材友情交换〓 - 矿石收音机论坛 - Powered by Discuz!

Theragun Elite (white) pictures to support recent teardown efforts.

Still not found a battery source.

⟐ Answered October 12, 2025 at 15:26 MST

My Conair pro airbrush turns on but doesn’t rotate.

Please guide me on how to fix it thank you.

Thank you

⟐ Commented May 28, 2024 at 19:19 MST

⟐ Commented November 08, 2018 at 11:46 MST

I would like to ask how to change the battery on Philips hair clipper DIY QC5580

Please help

⟐ Commented March 10, 2026 at 21:33 MST

⟐ Commented August 09, 2024 at 7:56 MST

⟐ Commented January 17, 2024 at 21:57 MST

⟐ Answered November 28, 2022 at 2:24 MST

⟐ Commented October 29, 2024 at 11:52 MST

So has anyone got any suggestions??

When I undo the screws I see a complex circuit board type thing. I don't know where to start even.

Going by what I can see, it appears the fuse has blown. It should be clear, however it is slightly brown in one section, so im guessing that's the part which will need to be replaced?

Next question, where can you buy fuse's from? can you even buy them/replace them?

I noticed the device fuse says 125V 6.3 A - What does this mean?

Regardless, the way I see things is, it's already broken, nothing worst can possibly be done to it so anyone who knows anything about burnt out things, any suggestions count.

Thanks!

EDIT: Okay this is the part I took out:

I'm not sure if the little 'cap' you see at either side should have came off, but I couldnt manage to take the cap off the fuse, as a result of that the fuse broke in half (as you can see). I tried to get a close up picture of EXACTLY what the fuse says. One side states "125V" the other side states "3G 6.3A" I understand that the 6.3A is the amps? Not sure about the 3G part though.

I'm from Australia and I've contacted a few department stores and they have been telling me that a lot of AU stores wont stock "125V", So now I'm looking to eBay.

I'm guessing I will need to buy a fuse that has the hooks at either side, since the caps came off when the fuse broke and otherwise there would be no way of holding them in place.

If you could be so kind as to perhaps post a link to eBay with the correct fuse I need I'd be very grateful.

Thanks again!

NEW EDIT:

This is what the whole board looks like

This is a close up of the place where the fuse was taken from

This is the reverse side

https://d3nevzfk7ii3be.cloudfront.net/ig...

These are the opposite side of where the fuse was sticking out

https://d3nevzfk7ii3be.cloudfront.net/ig...

⟐ Commented February 24, 2023 at 17:23 MST

To give you the backstory, as this may help out others, I bought this as a gift for my wife, but the device would not take a charge. We returned this to the retailer who exchanged it for another new device, but that had the same fault. Looks like there are hundreds of them with dud batteries.

Having done our research this is a really common fault and we were advised by the manufacturer that it would be best to replace with them directly.

What they did was send us out a brand new unit, directly and asked us to "dispose" of the faulty one. That doesn't seem like the right thing to do, so I wanted to see if I could do a repair on this and then give this to a family member.

However, I can't get much further than this (see pics)

I don't want to wreck the casing any more than I have done already. Any suggestions with annotations and arrows would be very helpful :)

⟐ Commented December 22, 2024 at 0:53 MST

⟐ Commented June 12, 2025 at 22:18 MST

⟐ Commented April 15, 2025 at 18:20 MST

I'm an elderly woman, don't have a solder thingy. is there any hope?

⟐ Commented August 06, 2023 at 5:50 MST

⟐ Answered July 06, 2021 at 9:25 MST

⟐ Commented August 20, 2025 at 8:51 MST

Thank you,

Brian Rodgers

⟐ Commented November 20, 2020 at 5:10 MST

⟐ Commented December 19, 2025 at 13:26 MST

⟐ Commented June 29, 2025 at 13:28 MST

⟐ Commented May 23, 2023 at 0:07 MST