⟐ Answer edited August 29, 2026 at 20:32 MST

⟐ Commented August 29, 2026 at 8:24 MST

⟐ Answer edited August 29, 2026 at 8:21 MST

⟐ Answer edited August 29, 2026 at 8:17 MST

⟐ Answered August 28, 2026 at 12:49 MST

Is there any way of reapplying it to make the repair OEM?

If someone does so, please let me know.

Thank you and good luck!

Cheers!

⟐ Answer edited August 28, 2026 at 13:12 MST

They are coming up as two separate Bluetooth devices in settings and I can only connect to one at a time.

Is there a way to force reset them?

Disclaimer: I cannot Reset through the app as that only works with two of them connected. Right now I'm the wearables app there are two separate devices.

⟐ Commented August 28, 2026 at 12:11 MST

⟐ Commented August 27, 2026 at 16:07 MST

⟐ Answer edited August 28, 2026 at 13:14 MST

They are a pair of black first generation Beats Studios.

Thanks! (:

This isn't the best pic of the crack, but here is what it looks like:

⟐ Answered August 26, 2026 at 19:17 MST

I have been trying to stick this with superglue but it keeps falling apart, even after waiting 10-20 minutes for it to cure. Can someone suggest alternative methods to stick this? The headphones work fine its just the slider thats broken.

⟐ Commented August 26, 2026 at 19:09 MST

⟐ Answered August 26, 2026 at 1:17 MST

⟐ Answer edited August 26, 2026 at 1:02 MST

⟐ Commented August 25, 2026 at 18:17 MST

⟐ Answer edited August 25, 2026 at 12:27 MST

Originally, the charging power kept dropping over time (about 3W → 2W → 1W → 0W) until it eventually stopped drawing any power at all. When I connected a charger and pressed the button, the LED would blink amber, and then it started blinking green. Even with the charger connected, the headphones wouldn’t function, and repeating the reset procedure didn’t help. If I unplugged the cable, there was no response at all, so I assumed the battery was completely drained and replaced the battery.

After replacing the battery, the only change is that the LED behavior went from blinking green to blinking amber—but nothing else improved. It still shows 0W draw even with the charger connected, and it won’t charge or power on.

In a case like this, what would you suspect as the likely cause? What parts or components would you recommend checking or replacing next, and what troubleshooting steps should I try?

Thanks in advance!

⟐ Commented August 25, 2026 at 8:47 MST

Symptoms:

My charging case is completely unresponsive. It does not show any LED light when connected to a USB-C cable (tried several certified PD chargers like Ugreen 30W and Baseus 65W).

Specific findings:

1. Overheating: When placed on a wireless charger (MagSafe style), the LED flashes amber momentarily and then fades. The bottom of the case becomes very hot within minutes.
2. Audible noise: If I hold the case to my ear while on the wireless charger, I can hear a fast, periodic clicking/chirping sound (likely a PMIC/controller stuck in a restart loop or "hiccup mode").
3. Reset: Holding the pairing button for 30+ seconds gives zero response.
4. Partial Passthrough: One earbud managed to get 5% charge after a long session on the wireless charger, even though the case itself remains dead.

What I've tried:

• Cleaned the USB-C port and internal pins with Isopropyl alcohol.
• Tried various power adapters and cables.
• Attempted factory reset multiple times.

Hypothesis: I suspect a short circuit on the main logic board or a failed PMIC. Given that the case is ultrasonically welded/glued, is there any known way to repair this without completely destroying the plastic shell? Are there common capacitor failures on this board?

⟐ Commented August 25, 2026 at 4:23 MST

⟐ Answered August 25, 2026 at 3:11 MST

⟐ Answer edited August 24, 2026 at 6:54 MST

⟐ Commented August 24, 2026 at 6:28 MST