⟐ Commented December 15, 2025 at 19:08 MST

⟐ Commented August 16, 2025 at 15:32 MST

⟐ Edited January 03, 2025 at 12:23 MST

I have a Frigidaire Model# FDB1500LFB0 and my problem is that…

after loading and selecting my cycle and hitting Start, my washer fills with water to the (I presume) proper amount of water in the bottom. The water is very hot. Then the system stops, and the only thing that will happen after opening it after this (anywhere from 3-15 minutes, I did this several times.) is that when the door is shut back and cancel pressed it will drain as normal. It was left to “run” once and the soap drawer opened, dumping the “pod” directly below it. The dishes had never had water on them and the “pod” was mushy from the ambient humidity, and in a spot directly under the drawer. If left on it will cycle through a fill/drain cycle but the spray-arms never move. I have cut the breaker to it on and off with no change.

Any help will be appreciated, thank you.

⟐ Edited May 21, 2024 at 9:22 MST

⟐ Answered November 01, 2025 at 9:23 MST

⟐ Commented September 05, 2024 at 6:54 MST

⟐ Answer accepted April 03, 2026 at 13:03 MST

⟐ Answer edited January 15, 2026 at 2:27 MST

⟐ Answered November 27, 2025 at 1:15 MST

⟐ Answered November 19, 2025 at 18:00 MST

⟐ Answered November 01, 2025 at 21:31 MST

I have a Frigidaire dishwasher, model FFID2426TS5A that won't force drain or start a cycle. When i apply power, the lights above the buttons all start up green, then the start/cancel light flashes. I try to force a drain (there's a small amount of water in the bottom of the dishwasher) and all lights go out on the button pad, and the dishwasher acts unresponsive until the next time I power cycle. It seems like a control board issue, but given the price of a control board, I would like to be 100% certain before I invest. Is there any way to know for sure?

Thanks, Ivan

⟐ Answer edited February 28, 2025 at 0:20 MST

⟐ Commented February 11, 2025 at 23:50 MST

⟐ Answer edited February 19, 2026 at 7:51 MST

The filters are clear. I disconnected the drain line in the basement and blew in it and the air will not go in.

Does this confirm that the hose is plugged?

Or do I have to pull out the dishwater and disconnect both ends and then do the blow test?

edit full model # is FFBD2406NW0A

⟐ Answer edited January 26, 2025 at 20:47 MST

⟐ Commented January 15, 2025 at 8:14 MST

There is no garbage disposal hooked up to it - no disposal at all.

I took the filters out of the basin prior to ordering the pump in case the issue was a clogged filter but after a good clean there was no change.

The drain hose is not clogged.

It makes sounds like it is draining but when it’s done and I open it up the entire basin (tub?) is full. This is true both before and after the pump replacement.

I’m about to order a pump and motor assembly but I don’t like to just throw parts at things when I’m not sure.

Anyone know what I should do? Is the pump assembly the right move? Is there something I’m overlooking?

Thanks

⟐ Answer accepted December 05, 2024 at 13:35 MST

It's a fridgid air gallery with the buttons on the top lip anti kid and is just a pull open no manual handle.

⟐ Answered March 15, 2024 at 12:25 MST

Any suggestions would be greatly appreciated

⟐ Commented August 05, 2023 at 8:10 MST

The quick wash could sometimes be longer than a normal cycle.

This has been going on for a few months now and I can't figure it out. It's before I start the cycles so its not about the turbidity sensor (I don't think).

I've tried resetting it by throwing the breaker for more than 5 mins and manual resets as well.

Any help would be appreciated.

⟐ Answer edited June 03, 2023 at 8:04 MST