iFixit - Answers With Device "Exercise Equipment"

Treadmill: Treadmill Motor control board bad?

Wed, 01 Apr 2026 02:52:22 -0700

My NordicTrack treadmill will power up and start fine but after 2 seconds the belt stops moving. The display is on but will not respond when I push the buttons. Once I power off and on it will again start but only runs for two seconds. I have checked the magnetic speed sensor and that is fine. I have also checked all the connections. When I look at the motor control board the red light is on u til the belt moves, then it blinks and goes back to solid red once it stops. Do you think the control board could be bad?

The model is a elite 9500.

⟐ Answered April 01, 2026 at 2:52 MST

Treadmill: لماذا جهاز المشي الخاص بي لا يتحرك و يقوم بإعطائي رمز الخطأ e01

Wed, 31 Dec 2025 03:58:01 -0700

جهاز المشي الخاص بي لا يقوم بالتحرك فعندما اقوم بتشغيله يقوم بإخراج صوت الطنين و يخرج لي على الشاشه الخاصه به رمز الخطأ e01

Treadmill: Treadmill Motor Control Board

Thu, 25 Dec 2025 21:49:12 -0700

Need the Circuit Schematics for a ProForm 730cs Treadmill Motor Control Board

⟐ Commented December 25, 2025 at 21:49 MST

Treadmill: Reebok treadmill zr9 display is not showing data

Tue, 25 Nov 2025 00:22:57 -0700

I am having a problem with my Reebok treadmill zr9 .it is suddenly the display is not showing any data, it is just a blue screen. Everything is working ,all buttons and settings but it is not showing on the screen

⟐ Commented November 25, 2025 at 0:22 MST

Treadmill: Why is my TA SPORT® treadmill power on but doesn't start working?

Tue, 25 Nov 2025 00:20:43 -0700

My TA SPORT® treadmill power on but doesn't start working? It was never broken or has no wire errors, there's no error code it just came as 3 hiphens on the screen. Help me out.

⟐ Answered November 25, 2025 at 0:20 MST

Treadmill: Broken Power Button Peloton Treadmill

Sun, 10 Aug 2025 07:52:49 -0700

The power button is a boat switch and it broke off during a recent move. Peloton is telling me the only solution is to replace the entire base of the treadmill. Can this be fixed?

⟐ Edited by author August 10, 2025 at 7:52 MST

Treadmill: Why does the remote not work on my homcom A90-131V70

Thu, 27 Mar 2025 03:34:13 -0700

I brought a second hand homcom A90-131V70 and the wireless remote doesn't power the treadmill however the buttons on the bottom works but not safe to use while using the treadmill

⟐ Answered March 27, 2025 at 3:34 MST

Treadmill: Treadmill goes full speed on start up.

Sat, 21 Sep 2024 04:45:31 -0700

I own a well used Reebok Edge REOM 11301 series treadmill. As soon as I switch it on the treadmill immediately goes top speed. I cannot turn the speed down and have to pull the emergency key out to stop the machine. I have looked everywhere for help and think maybe the problem is the speed sensor? I cannot locate the speed sensor to see if it has broken. I would really appreciate some guidance.

Many thanks.

⟐ Answer edited September 21, 2024 at 4:45 MST

Treadmill: Why does treadmill stop suddenly?

Sun, 02 Jun 2024 18:52:57 -0700

my cruze fitness CFT2020 stops suddenly and show error code E3.

⟐ Answered June 02, 2024 at 18:52 MST

Flexispot Standing Desk Bike: How do you replace the cranks?

Tue, 05 Mar 2024 07:24:38 -0700

I have stripped out the crank/pedal attachment. I have the replacement parts but can't figure out how to remove the set that is on the bike.

Thanks for your help.

⟐ Answered March 05, 2024 at 7:24 MST

Treadmill: NordicTrack 9.2 Why belt has started to working intermittently?

Fri, 29 Dec 2023 07:35:55 -0700

I have had this for 5 years and now suddenly it belt started to work intermittently..

Any pointers would be greatly appreciated

Thanks

⟐ Edited December 29, 2023 at 7:35 MST

Treadmill: Sole F63 motor control board

Sun, 27 Aug 2023 14:41:04 -0700

Need help identifying this component (yellow rectangle upper right corner pic #1), in the motor control board for my Sole 2014 F63 treadmill. I believe it's a fusible resistor but can't tell what size, value or type it is.If you know what it is, would you be so kind as to tell me where to get a replacement?

Not sure if this is the root of the original problem (see below) or just an added headache to slow me down and get me yelled at (even more).

Pics (labeled in to right corner)

#1: 1- believe to be bad fusible resistor (FR), 2- believed to be good FR ( Used for reference to check #1, 3- power indicating LED (On when power to board though transformer), 4- speed indicating LED(see below), 5- dark adhesive, capacitors have good (increasing) resistance

#2: test point 1-2 good conductivity with beep, 2-3 no beep 150k ohms

#3: test points 1-2 (not R5, but fuse 2) good conductivity with beep, 0.03 ohms

Original problem:
The display on my F63 treadmill 2014 will not come on (no lights or display values) after a loss of power (unplugged, power outage etc), and the speed indicating LED on the motor control board blinks when the treadmill belt is not moving, will blink quicker if I manually move the belt, and continues to blinks when I disconnect the speed sensor/reed switch. When I power the TM on it beeps a few times then the led begins to blink ,but no lights on the display. I can get the display to work by disconnecting/reconnecting wires on the motor control board and the ones that connect to the display board, never the same solution twice. When I check connectivity between the speed sensor connection on the mcb and the wires to the display board the led stops flashing. When the wires to the display board are disconnected the led is solid.

Thanks for any help.

Treadmill: Treadmill show error e6(1000+)and incline not going down and heat also

Fri, 11 Aug 2023 08:12:19 -0700

Incline motor heat and show error e6 what can we do?

⟐ Commented August 11, 2023 at 8:12 MST

Treadmill: The treadmill does not work when I press start

Sat, 01 Jul 2023 10:43:02 -0700

Everything it is OK but it doesn't work

Treadmill: Schematic diagram for Dunlop 9400 motor controller

Mon, 19 Jun 2023 23:49:38 -0700

I am looking for schematic diagram for Dunlop 9400 treadmill BC-1068 motor controller.

I tried to do beck engineering of the board but the ICs are cover with epoxy.

I found that the thermal sensor burned up, and must get schematic to replace it.

Schematic diagram for the BC-1068 or similar board will help.

Treadmill: The inclination of my treadmill does not work. What can it be?

Fri, 03 Mar 2023 09:04:07 -0700

II have a 1750 Commercial NordicTrack Treadmill and the slope system is not working. I've tried to calibrate, but to no avail. Someone can help me?

Treadmill: Why does my New Balance 1500 treadmill turn on and shut right off?

Mon, 02 Jan 2023 11:44:07 -0700

I was running on my New Balance 1500 treadmill and when I went to turn down the speed, I got shocked. At first it was like it froze up and just stayed on the speed I was at and then after a few minutes it just shut off. When I say shcoked I mean as in the way when you walk on carpet and then touch someone, that shock. I went through the manual and did everything they suggested, called New Balance (still waiting for a call back), left unplugged for a whole day and nothing works. When you first plug it in, the light comes on but then the machine just shuts right off. It's like it ins't connecting in the deck part, the area where you press power and speed and all that. Can anyone help me, please.

⟐ Answered January 02, 2023 at 11:44 MST

Treadmill: Sole F80 Treadmill Display Not Working-Fix With Smart Hacks

Thu, 22 Dec 2022 04:37:43 -0700

Previously, I told you how did I fix my friend’s Sole treadmill incline. In this post, you will learn to …for more click here

⟐ Answer accepted December 22, 2022 at 4:37 MST

Treadmill: Circuit control board not doing its job.

Wed, 16 Feb 2022 06:20:06 -0700

have a True brand treadmill, model 350 HRCB. Purchased in 2002 and still in excellent shape. Drive motor for the tread does not work. Everything else works fine. Had a treadmill service company come out to make the repair. They tested the motor by itself and found that it does work, but the controlling circuit board does not. So the motor will not run.

Searching for a replacement board has been unsuccessful from the manufacture or on the outside market.

Can the board be repaired???? Can anyone support and advise on these types of repairs?

Hello Jayeff and thank you for your reply. There is only one board in the treadmill and a photo of it was in the original post. I think that board controls the motor speed of the moving tread and the incline adjusting screw gear motor. The incline feature still works perfectly well, just the tread belt motor will not run. Here are a few more pictures of the board:

⟐ Commented February 16, 2022 at 6:20 MST

Treadmill: Brushes for motor Turdan A4D06J from Lifespan TR5000 Treadmill

Fri, 06 Aug 2021 00:06:24 -0700

Hello, where can I find brushes for the motor from Lifespan TR5000 Treadmill?

What kind of brushes are these, what model (product code)?
The brush is 16mm x 10mm and 18mm in lenght (guess 20-21mm new), cable 45mm
Marked with nr 62

Motor A4D06J made by TURDAN
H.P. 3 / RPM 2400 / ROTATION CW / DUTY CONT / VOLTS 210 / AMP 4.5 / FIELD PM

Thank you!

⟐ Commented August 06, 2021 at 0:06 MST