I purchased a Mavic Air 2S from EBay but I’m getting an error on the DJI Fly app that says

“Aircraft bound to another account. Change account and try again.”

I tried to reach the seller and no response. Is it possible to “unbind” the Air 2S from the previous owners DJI account?

⟐ Commented April 01, 2026 at 16:52 MST

⟐ Answered March 31, 2026 at 20:22 MST

I just bought a DJI mini 3 pro that turns out to have severe water damage (it's a little complicated, but I'm not too disappointed). Shockingly, it mostly works (no errors, only the rear right motor has a little more resistance than the rest so it can't quite fly); the previous owner didn't even know it was water damaged. It's been at least a week since it got wet, likely much longer. I'm going to follow this tutorial to clean off the motherboard, replace the ESC entirely, and probably follow the same steps for the camera module (is this safe?). However I have a couple questions:

1. What is that white stuff? It seems to have been used to glue some of the connectors, but whoever did this obviously didn't actually fix the water damage.
2. Should I do anything extra/differently because it's been corroding so long?
3. Can I do anything for the motors (flight and gimbal)?
4. Are there any listings for the thermal paste on amazon that could arrive quicker with prime? I couldn't find any.

⟐ Answered February 10, 2026 at 17:11 MST

• Replaced front left arm
  • Broke GPS ribbon cable
  • Small plastic cube came off the gimbal cable
• Replaced GPS ribbon cable with one from a M4p
  • Now flies
  • Gimbal stuck error (yaw/roll don't move, but all axes move manually)
• Replaced gimbal cable with one from a M4p
  • Damaged pitch motor ribbon cable during disassembly, replaced arm and motor with one from a M4p
  • Gimbal is now detached from the drone
  • No errors, gimbal moves when held
• Reattached gimbal
  • Gimbal does not move, no video feed
  • Tons of errors (see pictures)

I'm confused by the downward vision sensor error. I didn't mess with anything but the gimbal after I got it working while detached other than to try and address these issues.

⟐ Answered February 03, 2026 at 12:48 MST

⟐ Answered January 28, 2026 at 11:50 MST

Hi,

I was inquisitive to see which GPS module DJI used for this model, so I removed the shield. This disturbed a few components, as can be seen in the image, and didn't show the GPS chip.

Does any one know which way round the component bottom right should be or what it is?

I hope you find it interesting, but I suspect it may never work again.

P.S. I looked closer at the component, but it's not clear. Here's what I think it says on it: ASAXAF K61444T

P.P.S. When I removed the GPS shield, I used a pin in the small hole, which slid some components off.

I've just found that the shield is magnetic, so I could have used a magnet.

NOTE: BEWARE OF MAGNETIC COMPONENTS BEING ALSO LIFTED!

C

⟐ Edited by author January 05, 2026 at 3:33 MST

⟐ Answer accepted January 01, 2026 at 1:40 MST

⟐ Commented December 13, 2025 at 9:49 MST

⟐ Answered December 13, 2025 at 2:55 MST

Can anyone help me please?

Ange

⟐ Answered December 13, 2025 at 2:52 MST

I have reloaded de DJI Fly software and redo the activation procedure but the controller does connect with the drone and there is no message telling me to complete the activation and I have a message in the bottom right corner that says in french "Voir la camera"
But if I select this option it shoe that the unit is not activated.

What would be the other procedure to activate the unit.
Tank you for your help

⟐ Answered December 13, 2025 at 2:50 MST

⟐ Answered December 13, 2025 at 2:46 MST

⟐ Answered December 13, 2025 at 2:36 MST

⟐ Answered December 13, 2025 at 2:32 MST