iFixit - Answers With Device "Braava"

iRobot Braava 380t: Size Screws Needed To Attach The top Hard Cover to The vacuum

Sat, 21 Mar 2026 10:20:59 -0700

What size are the recessed screw that attach the outer cover to the Braava 380 to the remainder of the 380. They can be reached on the bottom side of the 380 with a screw just above each wheel and 2 additional screws just above the bar where the pad is attached.

iRobot Braava Jet M6: Left wheel sticking, error code 10

Sun, 13 Apr 2025 11:11:08 -0700

The app says there's a repair and replacement guide for wheel packs, but I can't find it in the app. Anybody done this repair and care to share?

iRobot Braava Jet M6: Why my charging station output is just around 3v?

Fri, 15 Dec 2023 13:54:31 -0700

The output voltage of the charging base measured with a voltmeter is around 3v (2,88 actually). Should it be at least 14,5 as stated on its bottom?

I just read somewhere around here that 2v might be a voltage set to detect the mop. When it runs across the mop it like knows it’s docked there and should built up to 1.5 amps resulting in 14.5 volts or something like this. Maybe there’s something wrong on the PCB which I examined, cleaned and on which connectors I applied some good old WD40 (for contact) without any luck.

⟐ Edited by author December 15, 2023 at 13:54 MST

iRobot Braava Jet M6: Flashing clean light on the Braava M6

Tue, 26 Sep 2023 09:17:20 -0700

Hi, My M6 only response is while it is docked the clean button just rapidly flashes increments of 3, but only when docked.

What I have seen through the troublshooting is that it is updating, but it has been doing this well over a week now. I called customer service and they said that it was the battery and it needed replaced. I purchased an aftermarket battery on ebay but when I installed it the exact same flashing cleaning light while docked. Ive seen this problem being mentioned a few times on forums but have yet to see a solution solved for the issue. Any advice?? thanks!

iRobot Braava Jet M6: The lid holder (transparent plastic piece) is broken and lost piece.

Sat, 17 Sep 2022 22:27:59 -0700

The lid holder (transparent plastic piece) is broken and lost the piece.

To keep the lid closed, we taped the lid (as you know when the lid is open it doesn’t start any jobs.)

Could you help me get a piece and fix the lid?

iRobot Braava Jet 240: How to remove this epoxy like glue?

Mon, 13 Jul 2020 09:46:52 -0700

Hi,

Anybody has ideas on how to remove this black, epoxy like(?) glue? (see pictures)

I tried heating it with hot air tool, but didn’t make any difference. It surrounds the cables, and worse, keeps the PCB in the case.

⟐ Commented July 13, 2020 at 9:46 MST

iRobot Braava 320: charges up, turns on but..

Mon, 09 Sep 2019 15:42:09 -0700

my IRobot Braava is fully charge and will turn on but that is all, it will not doing anything. Anyone have any suggestions?

⟐ Commented September 09, 2019 at 15:42 MST

iRobot Braava 320: Any idea how to fix a lost Battery Door for NorthStar Navigation Cube

Mon, 17 Sep 2018 02:44:22 -0700

I lost the battery door for the Cube and have tried various hacks, but get no stable result. Any Idea where I could get just the doors? I tried the thingverse 3D print database, but with no luck.

Any ideas for suppliers / hacks / printable files etc appreciated.

⟐ Edited by author September 17, 2018 at 2:44 MST

iRobot Braava 320: Mint 4200 not working with only a solid red nsi light.

Tue, 20 Feb 2018 13:16:15 -0700

Mint 4200 not working. (Same as Braava 320)

No beeps.

Only the middle nsi lamp turns on solid red. Same response if turned off and charger plugged in.

New battery.

Bumper is moving properly.

Rubber baffle strips are lying flat.

Rotated wheels with no effect.

iRobot Braava 380: Braava only backs up. Any suggestions as to the cause?

Fri, 22 Sep 2017 08:40:21 -0700

I went to use my Braava 380 and it seems like it works properly but it only backs up until it can't go any further and stops and beeps at me while flashing it's red light.

I'm pretty handy and can replace most parts but I need to know what is causing the problem? Any suggestions would be greatly appreciated.