I have two of these; one has been in storage in my unheated garage and the other in a desk drawer for the last several months. Both of them are exhibiting significant degradation of the display, along with this viscous fluid that's coming out of the seam between the rear cover and the frame of the tablet.

Now before anybody jumps to conclusions, no, neither of these laptops have ever been exposed to liquids; I've been all through them both and there's no external explanation for this to be happening.

And the thing is, I'm not the only one who's had this happen to them on this tablet. There's a whole thread over on the Acer forums of people who've had their laptops do the same thing.

Acer Iconia (W510P) Display Issue — Acer Community

I cleaned up the exterior of the laptop before I thought to take pictures, so I don't have photos of liquid that leaked out. It did clean up fairly easily with isopropyl alcohol.

My current working theory is that this is some sort of OCA that has broken down and returned to a liquid state. That's supported by what I see on the screen before powering it up; it looks like there are large air bubbles in the display.

You can see the bubbles in three corners of the screen. As you'll see from the following pictures, the display degradation is the same as what the people on the Acer forum experienced.

Once I got the back off of the tablet, I did find, as expected, more of the mystery liquid inside, concentrated in the lower right corner of the display.

Apparently there are a few older Dell laptops that seem to have the same problem, but in my internet searches I didn't find anyone who has had a definitive answer as to exactly what's going on here. Are there any experts on here who know what this is all about?

Obviously the displays on these tablets are shot, and unfortunately they're old and underpowered and realistically not worth repairing. However, I am going to go ahead and disassemble them and pull the LCDs to see if I can definitively pin the source to them, although I personally don't have any doubts myself.

This is going to be a bit of a slow process because I've decided to create some guides as I work, so it'll take longer than if I just tear into it.

Once I have the LCD out, I figure it can't hurt to see if it can be disassembled; who knows, maybe I can clean it and replace the OCA and effectively refurbish these defective screens.

Just as an update, I powered up the second W510 today and while it was messing around with updates I grabbed a photo of what its screen is doing.

⟐ Commented August 20, 2024 at 15:00 MST

⟐ Commented December 21, 2016 at 16:44 MST

⟐ Answer deleted September 15, 2018 at 0:23 MST

⟐ Answered October 06, 2016 at 10:38 MST

I I deleted Partition Recovery using “ MiniTool Partition Wizard “

The device was still working

But when rebooting, a blue square appears in the center

No Bootable Device.Hit any key

⟐ Commented February 08, 2019 at 2:45 MST

⟐ Answered July 20, 2023 at 11:45 MST

⟐ Answered April 28, 2017 at 8:31 MST

Added 3/22: I don’t have the tools to open up the tablet, and there are several variations of the SW5-017 series, but I think the USB-C port is mounted as shown in these photos of SW5-017 parts. Either directly to the motherboard (most likely for Generation 1 USB-C?) or on a daughterboard:

⟐ Commented March 24, 2022 at 8:15 MST

⟐ Answer deleted February 16, 2020 at 7:18 MST

⟐ Commented February 20, 2018 at 8:43 MST

⟐ Answered September 08, 2017 at 18:17 MST

When I switch it on, it will ask for me to draw my pattern that I can't remember. What can I do? The shop where I purchased it, they can't help.

I have tried to download drivers to my micro SD card for me to set it to factory setting. Nothing worked. When I press volume up and the switch, it gives me this message => FASTBOOT mode...

Any help.

⟐ Edited August 11, 2016 at 10:48 MST

⟐ Answer accepted May 02, 2016 at 4:34 MST

Especially interested in:

• Open Case
• CPU / Ram replacement if possible
• eMMC replacement if possible
• Battery replacement if possible

Thanks,

Manuel.

⟐ Commented July 11, 2018 at 9:28 MST

⟐ Answered February 21, 2025 at 12:59 MST

⟐ Answered March 13, 2025 at 10:23 MST

I have removed all the screws from the bottom of the machine but I can't seem to open it and there appears to be no other way in. Any advice please. I am hearing impaired and find YouTube unusable, as I can't concentrate on hearing and seeing at the same time. Written advice would be of great help - there isn't any that I can find on the Internet!

I'll probably use this machine with Linux (I tend to use Xubuntu) when I'm done messing about with its innards - if I can ever get to those innards!

⟐ Commented May 18, 2022 at 5:10 MST

It was on and just went blank

What must I do ?

⟐ Answered February 16, 2020 at 9:52 MST

I recently fixed a PC with a cooler broken.

My Iconia I think has the same problem.

I won’t buy the cooler now, thinking that you guys will see something diffrent.

Best regards,

Igor

⟐ Answer edited September 22, 2018 at 0:53 MST